Mitsubishi Galant. Manual — part 15
MAINTENANCE SERVICE
TSB Revision
GENERAL <BODY AND CHASSIS>
00-57
6. Check the clock spring connectors and protective tube for
damage, and terminals for deformities.
7. Visually check the case for damage.
WARNING
If the clock spring's mating mark is not properly
aligned, the steering wheel may not completely rotate
during a turn, or the flat cable within the clock spring
may be severed, obstructing normal operation of the
SRS and possibly leading to serious injury to the
vehicle's driver and passenger.
8. Align the mating marks of the clock spring, and after turning
the front wheels to the straight-ahead position, install the
clock spring to the column switch.
Mating Marks Alignment;
After turning the clock spring fully clockwise, turn it
approximately 3 turns counterclockwise until the mating
marks are aligned.
9. Install the steering column covers, steering wheel and air
bag module. (Refer to GROUP 52B, Air Bag Module and
Clock Spring
10.Check the steering wheel for noise, binds or difficult
operation.
DANGER
The SRS may not activate if any of the above
components are not installed properly, which could
result in serious injury or death to the vehicle's driver
and passenger.
11.Check the steering wheel for excessive free play.
ACX01302
CASE
PROTECTIVE
TUBES
AB
ACX00602 AB
MATING MARK
AC004928
AIR BAG
MODULE
AB
MAINTENANCE SERVICE
TSB Revision
GENERAL <BODY AND CHASSIS>
00-58
Front Seatback Assembly with Side Air Bag
Module
WARNING
•
If any improper part is found during the following
inspection, replace the front seatback assembly
with a new one.
•
Dispose of the old one according to the specified
procedure. (Refer to GROUP 52B, Air Bag Module
Disposal Procedures
.)
•
Never attempt to measure the circuit resistance of
the air bag module (squib) even if you are using
the specified tester. If the circuit resistance is
measured with a tester, accidental air bag
deployment will result in serious personal injury.
1. Check the air bag module deployment section for dents or
deformation.
2. Check the connector for damage, the terminals for
deformation, and harness for binds.
AC002988AB
AIR BAG MODULE
DEPLOYMENT
SECTION
MAINTENANCE SERVICE
TSB Revision
GENERAL <BODY AND CHASSIS>
00-59
Wiring Harness
WARNING
Replace any connectors or harness that fail the visual inspection. (Refer to GROUP 52B, SRS
Service Precautions
1. Check the connector for poor connection.
DANGER
The SRS system may not operate if SRS harnesses or connectors are damaged or
improperly connected, which could result in serious injury or death to the vehicle's driver
and passenger.
2. Check the harness for binds, the connectors for
damage, and the terminals for deformation.
20. EXHAUST SYSTEM
−−−−
CONNECTION PORTION
OF MUFFLER, MUFFLER PIPES AND
CONVERTER HEAT SHIELDS (CHECK AND
SERVICE AS REQUIRED)
M1001005800095
1. Check for holes and gas leaks due to damage, corrosion,
etc.
2. Check the joints and connections for looseness and gas
leaks.
3. Check the hanger rubber and brackets for damage.
AC004929
INSTRUMENT PANEL
WIRING HARNESS
FLOOR WIRING
HARNESS (LH)
SIDE AIR BAG
WIRING HARNESS
AB
FLOOR WIRING
HARNESS (RH)
MAIN SEALANT AND ADHESIVE TABLE
TSB Revision
GENERAL <BODY AND CHASSIS>
00-60
21. TIRES (ROTATE)
M1001008900109
Rotate tires regularly to equalize tire wear and help extend tire
life. Recommended tire rotation is every 12,000 km (7,500
miles) under normal driving conditions and every 9,600 km
(6,000 miles) in severe driving conditions.
Timing for the rotation may vary according to vehicle condition,
road surface conditions, and individual driver's habits.
When rotating tires, check for uneven wear, damage, and
wheel alignment. Abnormal wear is usually caused by
incorrect tire pressure, improper wheel alignment, out-of
balance wheels, or severe braking.
The first rotation is the most important to achieve more uniform
wear for all tires on the vehicle.
22. AIR PURIFIER FILTER (REPLACE)
M1001009000024
1. Remove the glove box and the front passenger's under
cover plug. (Refer to GROUP 52A, Instrument Panel
2. Pull the air purifier filter out through the plug hole of the front
passenger's under cover plug.
3. Insert a new air purifier into the blower assembly through the
plug hole. Attach the under cover plug, and install the glove
box.
M A IN SEA LA N T A N D A DH ESIVE TA B LE
M1001003800130
AC000120
AC004883 AB
AIR PURIFIER FILTER
APPLICATION
3M
NO.
LOCTITE
/
PERMATEX
NO.
ENGINE AND
DRIVETRAIN
Between rocker cover and
camshaft bearing cap.
Between rocker cover,
semicircular packing and
cylinder head. Between oil
pressure switch and engine.
3M
AAD Part No. 8660
Ultrapro High Temp.Silicone
Gasket or
3M
AAD Part No. 8679
Black/8678 Black Press-In-
Place Silicone gasket strips
Permatex
Ultra Black
598, No.82180
Between engine coolant
temperature switch, engine
coolant temperature sensor,
thermo valve, thermo switch,
joint, engine coolant
temperature gauge unit
(large-size) and engine
3M
AAD Part No. 8731
Medium Strength Blue
Threadlocker
Loctite
242 Blue Service
Tool Removable 24200
Between oil pan and engine
block
3M
AAD Part No. 8672,
3M
AAD Part No. 8704 or
3M
AAD Part No. 8679/
3M
AAD Part No. 8678 or
Permatex
Ultra Gray
599, No.82194
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст