Mitsubishi Galant. Manual — part 311
MULTIPORT FUEL INJECTION(MFI) DIAGNOSIS
TSB Revision
MULTIPORT FUEL INJECTION (MFI) <3.0L>
13B-469
STEP 2. Check the MFI relay
(1) Remove the MFI relay.
(2) Check for continuity between the MFI relay terminals 2 and
4.
•
There should be continuity (approximately 70
Ω
)
(3) Use jumper wires to connect MFI relay terminal 4 to the
positive battery terminal and terminal 2 to the negative
battery terminal.
(4) Check the continuity between the MFI relay terminals 1 and
3 while connecting and disconnecting the jumper wire at
the negative battery terminal.
•
Should be less than 2 ohm.(Negative battery terminal
connected)
•
Should be open loop.(Negative battery terminal
disconnected)
(5) Install the MFI relay.
Q: Is the voltage normal?
YES : Go to Step 3.
NO : Replace the MFI relay. Then confirm that the
malfunction symptom is eliminated.
STEP 3. Check the power supply voltage at MFI relay
harness side connector A-21X.
(1) Disconnect the connector A-21X and measure at the
harness side.
(2) Measure the voltage between terminal 3, 4 and ground.
•
Voltage should be battery positive voltage.
Q: Is the voltage normal?
YES : Go to Step 4.
NO : Check harness connector C-04 at intermediate
connector for damage, and repair or replace as
required. Refer to, GROUP 00E, Harness Connector
Inspection (
). If intermediate connector is in
good condition, repair harness wire between fusible
link (13) and MFI relay connector A-21X terminal 3, 4
because of open circuit. Then confirm that the
malfunction symptom is eliminated.
AK000555AB
CONNECTOR : A-21X
MFI RELAY
AK000369AB
MFI RELAY SIDE
CONNECTOR
1 2
3 4
AK000370AB
MFI RELAY SIDE
CONNECTOR
1 2
3 4
AK000371AB
1
2
3
4
A-21X HARNESS
SIDE CONNECTOR
MULTIPORT FUEL INJECTION(MFI) DIAGNOSIS
TSB Revision
MULTIPORT FUEL INJECTION (MFI) <3.0L>
13B-470
STEP 4. Check connector C-40 and C-41 at PCM for
damage.
Q: Is the connector in good condition?
YES : Go to Step 5.
NO : Repair or replace it. Refer to GROUP 00E, Harness
Connector Inspection (
). Then confirm that
the malfunction symptom is eliminated.
STEP 5. Check the ignition switch-IG signal voltage at PCM
harness side connector C-41.
(1) Disconnect the connector C-41 and measure at the harness
side.
(2) Turn the ignition switch to the "ON" position.
(3) Measure the voltage between terminal 98 and ground.
•
Voltage should be battery positive voltage.
(4) Turn the ignition switch to the "LOCK" (OFF) position.
Q: Is the voltage normal?
YES : Go to Step 6.
NO : Check harness connector C-04, C-66 and C-73 at
intermediate connector for damage, and repair or
replace as required. Refer to, GROUP 00E, Harness
Connector Inspection (
). If intermediate
connectors are in good condition, repair harness wire
between ignition switch connector C-58 terminal 2
and PCM connector C-41 terminal 98 because of
open circuit. Then confirm that the malfunction
symptom is eliminated.
STEP 6. Check the backup power supply voltage at PCM
harness side connector C-40.
(1) Disconnect the connector C-40 and measure at the harness
side.
(2) Measure the voltage between terminal 66 and ground.
•
Voltage should be battery positive voltage.
Q: Is the voltage normal?
YES : Go to Step 7.
NO : Check harness connector C-17 and C-66 at
intermediate connector for damage, and repair or
replace as required. Refer to, GROUP 00E, Harness
Connector Inspection (
). If intermediate
connectors are in good condition, repair harness wire
between fusible link (4) and PCM connector C-40
terminal 66 because of open circuit. Then confirm that
the malfunction symptom is eliminated.
AK000280
CONNECTORS : C-40, C-41
C-41
C-40
PCM
AX
AKX01435
71
72
73
74
75
76
77
89 88 87 86 858483 82 8180 7978
90
91
92
93
94
95
96
97
98
C-41 HARNESS
SIDE CONNECTOR
AD
AKX01436
41
42
43
44
45
46
57 56 55 54 53 52
48 47
58
59
60
61
62
66 65 64
63
51 50 49
C-40 HARNESS
SIDE CONNECTOR
AD
MULTIPORT FUEL INJECTION(MFI) DIAGNOSIS
TSB Revision
MULTIPORT FUEL INJECTION (MFI) <3.0L>
13B-471
STEP 7. Check the continuity at PCM harness side
connector C-40.
(1) Disconnect the connector C-40 and measure at the harness
side.
(2) Check for the continuity between terminal (42, 48) and
ground.
•
Should be less than 2 ohm.
Q: Is the continuity normal?
YES : Go to Step 8.
NO : Repair harness wire between PCM connector C-40
terminal (42, 48) and ground because of open circuit
or harness damage. Then confirm that the
malfunction symptom is eliminated.
STEP 8. Check the power supply voltage at PCM harness
side connector C-40.
(1) Disconnect the connector C-40 and measure at the harness
side.
(2) Measure the voltage between terminal 49 and ground.
•
Voltage should be battery positive voltage.
Q: Is the voltage normal?
YES : Go to Step 9.
NO : Repair harness wire between MFI relay connector A-
21X terminal 2 and PCM connector C-40 terminal 49
because of open circuit. Then confirm that the
malfunction symptom is eliminated.
STEP 9. Check the power supply voltage at PCM harness
side connector C-40.
(1) Disconnect the connector C-40 and measure at the harness
side.
(2) Using a jumper wire, connect terminal 49 to ground.
(3) Measure the voltage between terminal (41, 47) and ground.
•
Voltage should be battery positive voltage.
Q: Is the voltage normal?
YES : Replace the PCM. Then confirm that the malfunction
symptom is eliminated.
NO : Repair harness wire between MFI relay connector A-
21X terminal 1 and PCM connector C-40 terminal (41,
47) because of open circuit. Then confirm that the
malfunction symptom is eliminated.
AKX01437
46 45 44
43 42 41
47
48
49
50
51
52
53
54
55
56
57
66 65 64
63 62 6160
59 58
C-40 HARNESS
SIDE CONNECTOR
AE
AK000406
46 4544
43 42 41
47
48
49
50
51
52
53
54
55
56
66 6564
6362 6160
59 58
C-40 HARNESS
SIDE CONNECTOR
AC
AKX01438
46 45 44
43 42 41
47
48
49
50
51
52
53
54
55
56
57
66 65 64
63 62 6160
59 58
C-40 HARNESS
SIDE CONNECTOR
AE
MULTIPORT FUEL INJECTION(MFI) DIAGNOSIS
TSB Revision
MULTIPORT FUEL INJECTION (MFI) <3.0L>
13B-472
INSPECTION PROCEDURE 30: Fuel pump system.
M
AK000526
2
3 4
1 2 3
4
4 5 6
1 2
1
3
2
4 5
4
8
7
2
6
3
5
1
6
BL
ACK
-
WHITE
3
BL
ACK
-
WHITE
1
BL
ACK
-
WHITE
BL
ACK
-
WHITE
BL
ACK
-
WHITE
BL
ACK
-
WHITE
5
VIOLET
WHITE-BL
ACK
WHITE-
BL
ACK
WHITE-
BL
ACK
BL
ACK
IG2
ST
LOCK
ACC
IG1
C-58
2
5
C-04
MU801333
29
JUNCTION
BLOCK
R
C-73
MU801331
IGNITION
SWITCH
3
POWERTRAIN CONTROL
MODULE(PCM)
FUEL PUMP
AND GAUGE UNIT
FUEL PUMP RELAY
A-20X
3
4
1
2
21
6
D-14
(MU802058)
5
4
5
4
15 16
26 27 28 29
32 33 34
17 18 19 20 21 22 23 24 25
30 31
36 37
35
38
10
11 12 13
1 2 3
4 5 6 7 8 9
14
C-66
C-17
7 8
5
3 4
35
34
10 11 12
2122 23 24
13 14 15
25 26 27
16
28
17
18 19 20
29
30 31
32 33
36 37
38
9
1 2
6
C-39
(MU803784)
2
3 4
5 6
7 8
9
11 12 13 14 15 16 17 18 19 20
30
21 22 23
24 25
26 27 28 29
3132 33
34 35
1
10
1 2 3 4 5
6 7 8 9 10
1112 13 14 1516 171819 20 2122
C-71
MU801461
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст