Mitsubishi Galant. Manual — part 368
AUTO-CRUISE CONTROL
TSB Revision
ENGINE AND EMISSION CONTROL
17-42
STEP 5. Check the ground circuit voltage at auto-cruise
control-ECU connector C-52 by backprobing.
(1) Do not disconnect auto-cruise control-ECU connector C-52.
(2) Turn the ignition switch to "ON" position.
(3) Measure the voltage between terminal 14 and ground by
backprobing.
(4) Turn the ignition switch to "LOCK" (OFF) position.
Q: Is the voltage approximately 0.5 volts or less?
YES : Go to Step 8.
NO : Go to Step 6.
STEP 6. Check auto-cruise control-ECU connector C-52.
Q: Is the connector damaged?
YES : Repair or replace connector.
Refer to GROUP 00E, Harness Connector Inspection
.
Then check that the malfunction is eliminated.
NO : Go to Step 7.
STEP 7. Check the harness wire between auto-cruise
control-ECU connector C-52 and ground.
Q: Is any harness wire between auto-cruise control-ECU
connector C-52 and ground damaged?
YES : Repair the harness wire and then check that the
malfunction is eliminated.
NO : Check that the malfunction is eliminated.
If the malfunction is eliminated, replace the auto-
cruise control-ECU. (Refer to
.)
Then check that the malfunction is eliminated.
1 2 3 4 5 6 7 8
9 10 11 12 13 14 15 16
ACX01903
C-52 CONNECTOR
HARNESS SIDE VIEW
AD
AC004572AB
CONNECTOR: C-52
AC004572AB
CONNECTOR: C-52
AUTO-CRUISE CONTROL
TSB Revision
ENGINE AND EMISSION CONTROL
17-43
STEP 8. Check the output circuit voltage at data link
connector C-23.
(1) Turn the ignition switch to "ON" position.
(2) Measure the voltage between terminal 13 and ground.
(3) Turn the ignition switch to "LOCK" (OFF) position.
Q: Is the voltage approximately 4 volts or more?
YES : Check that the malfunction is eliminated.
If the malfunction is eliminated, replace the auto-
cruise control-ECU. (Refer to
.)
Then check that the malfunction is eliminated.
NO : Go to Step 9.
STEP 9. Check data link connector C-23.
Q: Is the connector damaged?
YES : Repair or replace connector.
Refer to GROUP 00E, Harness Connector Inspection
.
Then check that the malfunction is eliminated.
NO : Go to Step 10.
1 2 3 4 5 6 7 8
9 10 11 12 13 14 15 16
ACX01921AD
DATA LINK
CONNECTOR: C-23
AC004591
CONNECTOR: C-23
AB
AUTO-CRUISE CONTROL
TSB Revision
ENGINE AND EMISSION CONTROL
17-44
STEP10. Check the output circuit voltage at auto-cruise
control-ECU connector C-52 by backprobing.
(1) Do not disconnect auto-cruise control-ECU connector C-52.
(2) Turn the ignition switch to "ON" position.
(3) Measure the voltage between terminal 11 and ground by
backprobing.
(4) Turn the ignition switch to "LOCK" (OFF) position.
Q: Is the voltage approximately 4 volts or more?
YES : Go to Step 11.
NO : Go to Step 12.
STEP 11. Check the harness wire between auto-cruise
control-ECU connector C-52 and data link connector C-23.
Q: Is any harness wire between auto-cruise control-ECU
connector C-52 and data link connector C-23 damaged?
YES : Repair the harness wire and then check that the
malfunction is eliminated.
NO : Check that the malfunction is eliminated.
If the malfunction is eliminated, replace the auto-
cruise control-ECU. (Refer to
.)
Then check that the malfunction is eliminated.
1 2 3 4 5 6 7 8
9 10 11 12 13 14 15 16
ACX01904
C-52 CONNECTOR
HARNESS SIDE VIEW
AD
AC004572AB
CONNECTOR: C-52
AC004591
CONNECTOR: C-23
AB
AUTO-CRUISE CONTROL
TSB Revision
ENGINE AND EMISSION CONTROL
17-45
STEP 12. Check auto-cruise control-ECU connector C-52.
Q: Is the connector damaged?
YES : Repair or replace connector.
Refer to GROUP 00E, Harness Connector Inspection
.
Then check that the malfunction is eliminated.
NO : Check that the malfunction is eliminated.
If the malfunction is eliminated, replace the auto-
cruise control-ECU. (Refer to
.)
Then check that the malfunction is eliminated.
AC004572AB
CONNECTOR: C-52
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст