Mitsubishi Eclipse / Eclipse Spyder (2000-2002). Service and repair manual — part 62
![](/vehicles/winoney/isene/butrele/ret.png)
INTAKE MANIFOLD AND FUEL PARTS
TSB Revision
ENGINE OVERHAUL <3.0L ENGINE>
11D-19
INSTALLATION SERVICE POINTS
>>A<< INTAKE MANIFOLD INSTALLATION
1. Tighten the nuts "R" to 6.4
±
1.5 N
⋅
m (57
±
13 in-lb).
2. Tighten the nuts "L" to the specified torque.
Tightening torque: 22
±
1 N
⋅
m (16
±
1 ft-lb)
3. Tighten the nuts "R" to the specified torque.
Tightening torque: 22
±
1 N
⋅
m (16
±
1 ft-lb)
4. Tighten the nuts "L" to the specified torque.
Tightening torque: 22
±
1 N
⋅
m (16
±
1 ft-lb)
5. Tighten the nuts "R" to the specified torque.
Tightening torque: 22
±
1 N
⋅
m (16
±
1 ft-lb)
>>B<< INJECTOR INSTALLATION
CAUTION
Use care not to let engine oil enter the fuel rail.
1. Apply clean engine oil to the O-ring.
2. Insert the injector into the fuel rail.
3. Make sure the injector rotates smoothly. If not, remove the
injector to check the O-ring for damage, and replace the O-
ring if necessary. Then reinsert the injector and check that it
rotates smoothly.
4. Align the projection on the injector connector with the mating
mark on the fuel rail.
>>C<< FUEL PRESSURE REGULATOR INSTALLATION
CAUTION
Do not let engine oil enter the fuel rail.
1. Apply clean engine oil to the O-ring.
2. Insert the fuel pressure regulator into the fuel rail.
3. Make sure the regulator rotates smoothly. If not, remove the
fuel pressure regulator to check the O-ring for damage, and
replace the O-ring if necessary. Then reinsert the fuel
pressure regulator and check that it rotates smoothly.
4. Tighten the two bolts to the specified torque.
11. CONED DISC SPRING
>>A<<
12.INTAKE MANIFOLD
13.INTAKE MANIFOLD GASKET
REMOVAL STEPS (Continued)
AKX00680
TIMING
BELT SIDE
NUT "R"
NUT "L"
AB
AKX00748
FUEL RAIL
INJECTOR
AB
AKX00690
PROJECTION
AB
MATING
MARK
![](/vehicles/winoney/isene/butrele/jererdi.png)
WATER PUMP & WATER HOSE
TSB Revision
ENGINE OVERHAUL <3.0L ENGINE>
11D-20
Tightening torque: 8.8
±
1 N
⋅
m (78
±
9 in-lb)
WATER PU M P & WATER H O SE
REMOVAL AND INSTALLATION
M1113017900026
AKX00669
19 ± 1 N·m
14 ± 1 ft-lb
19 ± 1 N·m
14 ± 1 ft-lb
19 ± 1 N·m
14 ± 1 ft-lb
19 ± 1 N·m
14 ± 1 ft-lb
11 ± 1 N·m
95 ± 9 in-lb
29 ± 10 N·m
22 ± 7 ft-lb
14 ± 1 N·m
122 ± 9 in-lb
19 ± 1 N·m
14 ± 1 ft-lb
41 ± 8 N·m
30 ± 6 ft-lb
(M10 BOLT)
24 ± 3 N·m
17 ± 2 ft-lb
(M8 BOLT)
4
5
6
3
9
7
10
3
11
1
13
2
17
14
15
16
19
18
N
N
N
N
N
N
N
AB
8
12
REMOVAL STEPS
>>D<<
1. ENGINE COOLANT
TEMPERATURE GAUGE UNIT
>>C<<
2. ENGINE COOLANT
TEMPERATURE SENSOR
3 WATER HOSE
4. WATER HOSE
5. HEATER INLET PIPE
6. O-RING
7. HEATER OUTLET PIPE
8. O-RING
9. WATER OUTLET FITTING
GROMMET
REMOVAL STEPS (Continued)
![](/vehicles/winoney/isene/butrele/wequtod.png)
WATER PUMP & WATER HOSE
TSB Revision
ENGINE OVERHAUL <3.0L ENGINE>
11D-21
INSTALLATION SERVICE POINTS
>>A<< O-RING AND WATER INLET PIPE INSTALLATION
CAUTION
Keep the O-ring free of oil or grease.
1. Attach a new O-ring to each end of the water inlet pipe.
2. Wet the O-ring with water.
3. Insert the front end of the pipe into the water pump.
>>B<< THERMOSTAT INSTALLATION
1. Check that the rubber ring is free from damage and seated
correctly in the thermostat flange.
2. Install the thermostat as shown in the illustration. The jiggle
valve must be at the uppermost position.
>>C<< SEALANT APPLICATION TO ENGINE COOLANT
TEMPERATURE SENSOR
Apply 3M
AAD Part number 8731 or equivalent to the engine
coolant temperature sensor.
10.GASKET
11. WATER INLET FITTING
>>B<<
12.THERMOSTAT
13.THERMOSTAT HOUSING
14.GASKET
>>A<<
15.O-RING
>>A<<
16.WATER INLET PIPE
>>A<<
17.O-RING
18.WATER PUMP
19.WATER PUMP GASKET
REMOVAL STEPS (Continued)
AKX00711
O-RING
WATER INLET
PIPE
AB
AKX00670AB
JIGGLE VALVE
AKX00686
![](/vehicles/winoney/isene/butrele/fiarteb.png)
WATER PUMP & WATER HOSE
TSB Revision
ENGINE OVERHAUL <3.0L ENGINE>
11D-22
>>D<< SEALANT APPLICATION TO ENGINE COOLANT
TEMPERATURE GAUGE UNIT
Apply 3M
AAD Part number 8672 or equivalent to the engine
coolant temperature gauge unit.
AKX00687
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст