Mitsubishi Eclipse / Eclipse Spyder (2000-2002). Service and repair manual — part 558
SPECIAL TOOLS
TSB Revision
REAR SUSPENSION
34-5
SPECIA L TO O LS
M1341000600079
O N -VEH IC LE SERVIC E
REAR WHEEL ALIGNMENT CHECK AND
ADJUSTMENT
M1341011000071
Measure wheel alignment with an alignment equipment on
level ground.
The rear suspension and wheels should be serviced to the
normal condition prior to wheel alignment.
TOOL
TOOL NUMBER AND
NAME
SUPERSESSION
APPLICATION
•
A: MB991237
Spring compressor
body
•
B: MB991239
Arm set
MIT221369
Coil spring removal and
installation
MB990635 or MB991113
Steering linkage puller
MB991113-01 MB990635-
01 or General service tool
Ball joint disconnection
MB990326
Preload socket
General service tool
Ball joint rotating torque
check
MB990800
Ball joint remover and
installer
MB990800-01 or General
service tool
Dust cover installation
MB991237
A
B
MB990635
MB990326
MB990800
REAR SUSPENSION ASSEMBLY
TSB Revision
REAR SUSPENSION
34-6
TOE-IN
Standard value: 3
±
3 mm (0.12
±
0.12 inch)
Loosen nut, then turn the toe control arm mounting bolt to
adjust toe.
NOTE:
.
•
LH: Clockwise viewed from the rear
→
Toe-out
•
RH: Clockwise viewed from the rear
→
Toe-in
•
Toe adjustment can be made at graduations of
approximately 2.5 mm (0.10 inch).
CAMBER
Standard value:
<ECLIPSE>
−
1
°
20'
±
30' (Difference between right
and left within 30')
<ECLIPSE SPYDER>
−
1
°
10'
±
30' (Difference
between right and left within 30')
NOTE: Camber is preset at the factory and cannot be adjusted.
NOTE: If camber is not within the standard value, check and
replace bent or damaged parts.
BALL JOINT DUST COVER INSPECTION
M1341012800081
1. Check dust covers for cracks or damage by pushing it with
your finger.
2. If a dust cover is cracked or damaged, replace the toe
control arm assembly or stabilizer link.
NOTE: Cracks or damage to the dust cover may cause
damage to the ball joint.
R EAR SU SPENSIO N A SSEM BLY
REMOVAL AND INSTALLATION
M1341001000036
CAUTION
*
: Indicates parts which should be temporarily tightened, and then fully tightened with the vehicle on
the ground in the unladen condition.
AC001056AB
CROSSMEMBER
Pre-removal Operation
•
Fully Close Convertible Top Assembly. <ECLIPSE SPY-
DER>
•
Brake Fluid Draining <Vehicles with drum brake>
•
Service Lid Removal <ECLIPSE> (Refer to GROUP 52A,
Trims
•
Center Exhaust Pipe Removal (Refer to GROUP 15,
Exhaust Pipe and Main Muffler
and
Post-installation Operation
•
Center Exhaust Pipe Installation (Refer to GROUP 15,
Exhaust Pipe and Main Muffler
and
•
Service Lid Installation <ECLIPSE> (Refer to GROUP
52A, Trims
•
Parking Brake Lever Stroke Check (Refer to GROUP 36,
On-vehicle Service
−
Parking Brake Lever Stroke Check
and Adjustment
•
Brake Line bleeding <Vehicles with drum brake> (Refer to
GROUP 35A, On-vehicle Service
−
Bleeding
.)
•
Wheel Alignment Check and Adjustment (Refer to
REAR SUSPENSION ASSEMBLY
TSB Revision
REAR SUSPENSION
34-7
AC003096
N
8
13
44 ± 5 N·m
33 ± 3 ft-lb
AC
14
7
6
5
4
3
2
1
39 ± 5 N·m
29 ± 4 ft-lb
88 ± 10 N·m
65 ± 7 ft-lb
60 ± 5 N·m
45 ± 3 ft-lb
15
11
11
12
10
9
15 ± 2 N·m
11 ± 1 ft-lb
147 ± 10 N·m*
109 ± 7 ft-lb*
REMOVAL STEPS
<<A>>
.
•
DRAIN TURF MOUNTING HOOK
<ECLIPSE SPYDER>
1.
CAP
2.
SHOCK ABSORBER MOUNTING
NUTS
<<B>>
3.
BRAKE CALIPER ASSEMBLY
4.
BRAKE DISC OR BRAKE DRUM
5.
SHOE AND LINING ASSEMBLY
(DRUM BRAKE: REFER TO
GROUP 36, PARKING BRAKE
CABLE
. /DRUM-IN-DISC
BRAKE: REFER TO GROUP 36,
PARKING BRAKE CABLE
6.
PARKING BRAKE CABLE
CONNECTION (DRUM BRAKE:
REFER TO GROUP 36, PARKING
BRAKE CABLE
. /DRUM-IN-
DISC BRAKE: REFER TO GROUP
36, PARKING BRAKE CABLE
7.
BRAKE HOSE CONNECTION
<VEHICLES WITH DRUM BRAKE>
8.
UPPER ARM MOUNTING BOLTS
9.
GROMMET
10. TRAILING ARM MOUNTING BOLT
>>A<<
11. STOPPER A
>>A<<
12. STOPPER B
<<C>>
13. CROSSMEMBER MOUNTING NUT
14. REAR WHEEL SPEED SENSOR
CONNECTOR CONNECTION
<VEHICLES WITH ABS>
15. REAR SUSPENSION ASSEMBLY
REMOVAL STEPS (Continued)
REAR SUSPENSION ASSEMBLY
TSB Revision
REAR SUSPENSION
34-8
REMOVAL SERVICE POINTS
<<A>> DRAIN TURF MOUNTING HOOK REMOVAL
<ECLIPSE SPYDER>
Remove the drain turf mounting hook so that the cap can be
seen from the passenger compartment.
<<B>> BRAKE CALIPER ASSEMBLY REMOVAL
Secure the removed caliper assembly with a wire, so that it
does not fall.
<<C>> CROSSMEMBER MOUNTING NUT REMOVAL
Support the crossmember with a garage jack or transmission
jack to remove the crossmember mounting nut.
AC004074AB
REAR GLASS
DRAIN TURF
AC001058
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст