Mitsubishi Eclipse / Eclipse Spyder (2000-2002). Service and repair manual — part 526
TRANSAXLE
TSB Revision
AUTOMATIC TRANSAXLE OVERHAUL
23B-35
CAUTION
Do not reuse the bolt, as it has had sealant applied.
24.Tighten the mounting bolts of the output shaft bearing
retainer to the specified torque.
Tightening torque:
23
±
3 N
⋅
m (17
±
2 ft-lb) <F4A42>
54
±
5 N
⋅
m (40
±
4 ft-lb) <F4A51>
25.Use special tool MD998350 to install the collar and taper
roller bearing on the output shaft.
26.Apply ATF to a new jam nut, and use special tools
MB990607 and MB991625 to tighten the jam nut to the
specified torque. Then turn back one turn, and tighten to the
specified torque again.
Tightening torque: 167
±
10 N
⋅
m (123
±
7 ft-lb)
NOTE: The jam nut is reverse threaded.
AKX01038
AKX01061
MD998350
AB
AKX01062
MB991625
MB990607
AB
TRANSAXLE
TSB Revision
AUTOMATIC TRANSAXLE OVERHAUL
23B-36
27.Move the output shaft to measure the end play and record
the measurement value.
28.Remove the parts that were installed in steps 21 to 25.
29.Add 1.88 mm (0.074 inch)* and 0.01 to 0.09 mm (0.0004 to
0.0035 inch)** to the measured value in step 26 and select a
spacer of the same thickness. Adjustment spacer sizes are
all listed on page 23B-79. Select the most suitable one from
among those listed.
NOTE: * is the thickness of the spacer installed in step 21. **
is the preload of the output shaft.
30.Repeat steps 22 to 25 again, installing each part and using
the appropriate adjustment spacer determined in step 27.
31.Stake the jam nut with a punch (two places).
32.Use special tools MB990931 and MB990938 to install the
cap as shown in the illustration.
33.Install the parking pawl, spacer, and spring. Then insert the
parking pawl shaft.
34.Install the parking roller support, and then insert the two
parking roller support shafts.
AKX01063
AKX01064
AKX01065
MB990938
MB990931
AB
2.5-3.0mm
(0.098 - 0.118in)
AKX01066AB
PARKING PAWL SHAFT
AKX01067
PARKING ROLLER
SUPPORT SHAFTS
AB
TRANSAXLE
TSB Revision
AUTOMATIC TRANSAXLE OVERHAUL
23B-37
IDENTIFICATION OF THRUST BEARING, THRUST RACES,
AND THRUST WASHERS
mm (in)
AKX01108
No. 8
No. 7
No. 6
No. 5
No. 4
No. 3
No. 2
No. 1
(SELECT)
(SELECT)
AB
SYMBOL
OD
ID
THICKNESS
PART NO.
APPLICATION
No.1
59 (2.32)
47 (1.85)
1.8 (0.071)
MD754509
59 (2.32)
47 (1.85)
2.0 (0.079)
MD754508
59 (2.32)
47 (1.85)
2.2 (0.087)
MD754507
59 (2.32)
47 (1.85)
2.4 (0.094)
MD753793
59 (2.32)
47 (1.85)
2.6 (0.102)
MD753794
59 (2.32)
47 (1.85)
2.8 (0.110)
MD753795
49 (1.93)
36 (1.42)
3.6 (0.142)
MD756846
No.3
49 (1.93)
36 (1.42)
3.6 (0.142)
MD756846
45.3 (1.783)
31 (1.22)
3.3 (0.130)
MD757647
F4A42
55.4 (2.181)
38.5 (1.516)
3.3 (0.130)
MD761683
F4A51
No.5
49 (1.93)
36 (1.42)
3.6 (0.142)
MD756846
F4A42
TRANSAXLE
TSB Revision
AUTOMATIC TRANSAXLE OVERHAUL
23B-38
35.Install the planetary carrier assembly.
36.Install the planetary reverse sun gear.
57 (2.244)
38.5 (1.516)
4.1 (0.161)
MD758556
F4A51
No.6
49 (1.93)
36 (1.42)
3.6 (0.142)
MD756846
F4A42
57 (2.244)
38.5 (1.516)
4.1 (0.161)
MD758556
F4A51
No.7
59 (2.32)
37 (1.46)
2.8 (0.110)
MD754595
No.8
48.9 (1.925)
37 (1.46)
1.6 (0.063)
MD707267
48.9 (1.925)
37 (1.46)
1.7 (0.067)
MD759681
48.9 (1.925)
37 (1.46)
1.8 (0.071)
MD723064
48.9 (1.925)
37 (1.46)
1.9 (0.075)
MD754794
48.9 (1.925)
37 (1.46)
2.0 (0.079)
MD707268
48.9 (1.925)
37 (1.46)
2.1 (0.083)
MD754795
48.9 (1.925)
37 (1.46)
2.2 (0.087)
MD723065
48.9 (1.925)
37 (1.46)
2.3 (0.091)
MD754796
48.9 (1.925)
37 (1.46)
2.4 (0.094)
MD724358
48.9 (1.925)
37 (1.46)
2.5 (0.098)
MD754797
48.9 (1.925)
37 (1.46)
2.6 (0.102)
MD754798
SYMBOL
OD
ID
THICKNESS
PART NO.
APPLICATION
AKX01018
AKX01014
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст