Mitsubishi Galant (2004+). Manual — part 1373
DOOR MIRROR
TSB Revision
EXTERIOR
51-37
STEP 7. Check the wiring harness between remote
controlled mirror (LH) connector E-09 (terminal 1) and
junction block connector C-211 (terminal 3).
NOTE: Also check intermediate connector C-26 for loose, cor-
roded or damaged terminals, or terminals pushed back in the
connector. If intermediate connector C-26 is damaged, repair or
replace the damaged component(s) as described in GROUP
00E, Harness Connector Inspection
Q: Is the wiring harness between remote controlled mirror
(LH) connector E-09 (terminal 1) and junction block
connector C-211 (terminal 3) in good condition?
YES : No action is necessary and testing is complete.
NO : Repair the wiring harness as necessary. And then
check to see that the heater function of the door
mirror (LH) operates normally.
AC307125
E-09 (GR)
CONNECTOR: E-09
HARNESS SIDE
AC
AC307123
JUNCTION BLOCK (FRONT VIEW)
CONNECTOR: C-211
AB
AC307314
CONNECTOR: C-26
AB
DOOR MIRROR
TSB Revision
EXTERIOR
51-38
STEP 8. Check the remote controlled mirror (RH)
connector E-01 for loose, corroded or damaged terminals,
or terminals pushed back in the connector.
Q: Is the remote controlled mirror (RH) connector E-01 in
good condition?
YES : Go to Step 9.
NO : Repair or replace the damaged component(s). Refer
to GROUP 00E, Harness Connector Inspection
. And then check to see that the heater
function of the door mirror (RH) operates normally.
STEP 9. Check the heater function of the door mirror (RH).
CAUTION
When relocating the car between locations of extremely
different temperatures (warm and cold), leave the car in
the location for a while to adapt to the temperature prior to
checking it.
Check to see that the resistance shown in the graph is almost
satisfied when measuring the resistance between terminal 1
and 3 of the door mirror (RH) connector E-01.
Q: Is the resistance normal?
YES : Go to Step 10.
NO : Replace the door mirror (RH). And then check to see
that the heater function of the door mirror (RH)
operates normally.
AC307124
E-01 (GR)
CONNECTOR: E-01
HARNESS SIDE
AC
AC307177
RESISTANCE
TEMPERATURE (˚C)
-10
0
10
20
30
40
(
Ω)
0
2
4
6
8
10
AB
12
UPPER LIMIT VALUE
LOWER LIMIT VALUE
DOOR MIRROR
TSB Revision
EXTERIOR
51-39
STEP 10. Check the ground circuit between remote
controlled mirror (RH) connector E-01 and ground for open
circuit. Measure the resistance at remote controlled mirror
(RH) connector E-01.
(1) Disconnect remote controlled mirror (RH) connector E-01,
and check at the wiring harness side connector.
(2) Measure the resistance value between terminal 3 and
ground.
• The resistance should equal 2 ohms or less.
Q: Is the measured resistance 2 ohms or less?
YES : Go to Step 12.
NO : Go to Step 11.
STEP 11. Check the wiring harness between remote
controlled mirror (RH) connector E-01 (terminal 3) and
ground.
AC307124
E-01 (GR)
CONNECTOR: E-01
HARNESS SIDE
AC
AC307127
CONNECTOR: E-09
(HARNESS SIDE)
AB
AC307124
E-01 (GR)
CONNECTOR: E-01
HARNESS SIDE
AC
DOOR MIRROR
TSB Revision
EXTERIOR
51-40
NOTE: Also check intermediate connector C-12 for loose, cor-
roded or damaged terminals, or terminals pushed back in the
connector. If intermediate connector C-12 is damaged, repair or
replace the damaged component(s) as described in GROUP
00E, Harness Connector Inspection
Q: Is the wiring harness between remote controlled mirror
(RH) connector E-01 (terminal 3) and ground in good
condition?
YES : No action is necessary and testing is complete.
NO : The wiring harness may be damaged. Repair the
wiring harness as necessary. And then check to see
that the heater function of the door mirror (RH)
operates normally.
STEP 12. Check junction block C-211 for loose, corroded
damaged terminal, or terminals pushed back in the
connector.
Q: Is junction block C-211 in good condition?
YES : Go to Step 13.
NO : Repair or replace the damaged component(s). Refer
to GROUP 00E, Harness Connector Inspection
. And then check to see that the heater
function of the door mirror (RH) operates normally.
AC307120
CONNECTOR: C-12
AB
AC307121
JUNCTION BLOCK (FRONT VIEW)
CONNECTOR: C-211
AB
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст