Mitsubishi Galant (2004+). Manual — part 1372
DOOR MIRROR
TSB Revision
EXTERIOR
51-33
.
CIRCUIT OPERATION
If either of the heated door mirrors do not operate
normally, it may be due to malfunctions in the heated
door mirror circuit or door mirror.
.
TROUBLESHOOTING HINTS
• Malfunction of the heated door mirror circuit
• Malfunction of the door mirror
• The wiring harness or connectors may have
loose, corroded, or damaged terminals, or termi-
nals pushed back in the connector.
DIAGNOSIS
STEP 1. Verify the operation of each heated door mirror.
Q: Which door mirror does not heat?
Door mirror (LH) : Go to Step 2.
Door mirror (RH) : Go to Step 8.
AC307118
CONNECTOR: C-12
AB
AC307119
CONNECTOR: C-26
AB
AC307121
JUNCTION BLOCK (FRONT VIEW)
CONNECTOR: C-211
AB
AC307125
E-09 (GR)
CONNECTOR: E-09
AB
AC307124
E-01 (GR)
CONNECTOR: E-01
AB
DOOR MIRROR
TSB Revision
EXTERIOR
51-34
STEP 2. Check remote controlled mirror (LH) connector
E-09 for loose, corroded or damaged terminals, or
terminals pushed back in the connector.
Q: Is remote controlled mirror (LH) connector E-09 in good
condition?
YES : Go to Step 3.
NO : Repair or replace the damaged component(s). Refer
to GROUP 00E, Harness Connector Inspection
. And then check to see that the heater
function of the door mirror (LH) operates normally.
STEP 3. Check the heater of the door mirror (LH).
CAUTION
When relocating the car between locations of extremely
different temperatures (warm and cold), leave the car in
the location for a while to adapt to the temperature prior to
checking it.
Check to see that the resistance shown in the graph is almost
satisfied when measuring the resistance between terminal 1
and 3 of the remote controlled mirror (LH) connector E-09.
Q: Is the resistance normal?
YES : Go to Step 4.
NO : Replace the door mirror (LH). And then check to see
that the heater function of the door mirror (LH) is
operating normally.
AC307125
E-09 (GR)
CONNECTOR: E-09
HARNESS SIDE
AC
AC307177
RESISTANCE
TEMPERATURE (˚C)
-10
0
10
20
30
40
(
Ω)
0
2
4
6
8
10
AB
12
UPPER LIMIT VALUE
LOWER LIMIT VALUE
DOOR MIRROR
TSB Revision
EXTERIOR
51-35
STEP 4. Check the ground circuit to between remote
controlled mirror (LH) connector E-09 and ground for open
circuit. Measure the resistance at remote controlled mirror
(LH) connector E-09.
(1) Disconnect remote controlled mirror (LH) connector E-09
and check at the wiring harness side connector.
(2) Measure the resistance value between terminal 3 and
ground.
• The resistance should equal 2 ohms or less.
Q: Is the measured resistance 2 ohms or less?
YES : Go to Step 6.
NO : Go to Step 5.
STEP 5. Check the wiring harness between remote
controlled mirror (LH) connector E-09 (terminal 3) and
ground.
AC307125
E-09 (GR)
CONNECTOR: E-09
HARNESS SIDE
AC
AC307127
CONNECTOR: E-09
(HARNESS SIDE)
AB
AC307125
E-09 (GR)
CONNECTOR: E-09
HARNESS SIDE
AC
DOOR MIRROR
TSB Revision
EXTERIOR
51-36
NOTE: Also check intermediate connector C-26 for loose, cor-
roded or damaged terminals, or terminals pushed back in the
connector. If intermediate connector C-26 is damaged, repair or
replace the damaged component(s) as described in GROUP
00E, Harness Connector Inspection
Q: Is the wiring harness between remote controlled mirror
(LH) connector E-09 (terminal 3) and ground in good
condition?
YES : No action is necessary and testing is complete.
NO : The wiring harness may be damaged. Repair the
wiring harness as necessary. And then check to see
that the heater function of the door mirror (LH)
operates normally.
STEP 6. Check junction block C-211 for loose, corroded
damaged terminal, or terminals pushed back in the
connector.
Q: Is junction block C-211 in good condition?
YES : Go to Step 7.
NO : Repair or replace the damaged component(s). Refer
to GROUP 00E, Harness Connector Inspection
. And then check to see that the heater
function of the door mirror (LH) operates normally.
AC307314
CONNECTOR: C-26
AB
AC307121
JUNCTION BLOCK (FRONT VIEW)
CONNECTOR: C-211
AB
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст