Mitsubishi Galant (2004+). Manual — part 711
TRANSAXLE ASSEMBLY
TSB Revision
AUTOMATIC TRANSAXLE
23A-395
REMOVAL SERVICE POINTS
.
<<A>> DRIVE SHAFT NUT REMOVAL
CAUTION
Do not apply pressure to the wheel bearing by the vehicle
weight to avoid possible damage when the drive shaft nut
is loosened.
Use special tool MB990767 to fix the hub and remove the drive
shaft nut.
.
<<B>> LOWER ARM BALL JOINT/TIE ROD END
CONNECTION REMOVAL
CAUTION
• Do not remove the nut from ball joint. Loosen it and use
the special tool to avoid possible damage to ball joint
threads.
• Hang the special tool with cord to prevent it from fall-
ing.
1. Replace the self locking nut with a regular nut, because the
original one is a little bit large to install the special tool.
Install special tool MB991897 as shown in the figure.
2. Turn the bolt and knob as necessary to make the jaws of
special tool MB991897 parallel, tighten the bolt by hand and
confirm that the jaws are still parallel.
NOTE: When adjusting the jaws in parallel, make sure the
knob is in the position shown in the figure.
3. Tighten the bolt with a wrench to disconnect the tie rod end
and remove the self locking nut.
.
AC102462
AC
MB990767
AC208247AC
CORD
BOLT
MB991897
NUT
BALL JOINT
AC106821
KNOB
PARALLEL
BOLT
CORRECT
WRONG
AC
TRANSAXLE ASSEMBLY
TSB Revision
AUTOMATIC TRANSAXLE
23A-396
<<C>> DRIVE SHAFT REMOVAL
1. Use special tools MB990242, MB990244, MB991354 and
MB990767 to push out the drive shaft or the drive shaft and
inner shaft assembly from the hub.
2. Remove the drive shaft from the hub by pulling the bottom of
the brake disc towards you.
CAUTION
• Do not pull on the drive shaft; doing so will damage the
TJ; be sure to use the pry bar.
• When pulling the drive shaft out from the transaxle, be
careful that the spline part of the drive shaft does not
damage the oil seal.
3. Remove the drive shaft from the transaxle by the following
procedure. Insert a pry bar between the transaxle case and
the drive shaft, and then pry the drive shaft from the
transaxle.
CAUTION
Do not apply pressure to the wheel bearing by the vehicle
weight to avoid possible damage when the drive shaft is
removed. If, however, vehicle weight must be applied to
the bearing to move the vehicle, temporarily secure the
wheel bearing by using special tools MB991000 and
MB990998.
.
AC102550
MB990244
(THREE)
MB991354
MB990242
MB990767
AC
AC102551AD
DRIVE
SHAFT
AC100141AK
TRANSAXLE
TJ ASSEMBLY
PRY BAR
AC210315 AE
MB990998
MB991000
TRANSAXLE ASSEMBLY
TSB Revision
AUTOMATIC TRANSAXLE
23A-397
<<D>> TORQUE CONVERTEER AND DRIVE PLATE
COUPLING BOLTS REMOVAL
1. Remove the drive plate coupling bolts while turning the
crank shaft.
2. Pry the torque converter towards the transaxle side.
Remove the torque converter with the transaxle.
.
<<E>> ENGINE ASSEMBLY SUPPORTING
1. <Engine hanger (special tool MB991895) is used>
(1) Set special tool MB991895 (engine hanger) to the front
fender assembling bolts (A and B) and (C and D) as
shown.
(2) Set special tool MB991527 and MB991454 (chain) to
hold the engine/transaxle assembly.
2. <Engine hanger (special tool MB991928) is used>
(1) Assemble the engine hanger (special tool MB991928).
Attach following parts to the base hanger.)
• SLIDE BRACKET (HI)
• FOOT (STANDARD) (MB991932) <FRONT SIDE>
• JOINT (90) (MB991930)
• FOOT (SHORT) (MB991933) <REAR SIDE>
(2) Set special tool MB991928 (engine hanger) to the front
fender assembling bolts (A and B) and (C and D) as
shown.
AC306197
<RH>
<LH>
A
C
B
D
AB
AC306198
MB991527
MB991454
MB991895
AB
AC306199
AB
JOINT (90)
(MB991930)
FOOT
(STANDARD)
(MB991932)
FOOT
(SHORT)
(MB991933)
SLIDE
BRACKET (HI)
AC306197
<RH>
<LH>
A
C
B
D
AB
TRANSAXLE ASSEMBLY
TSB Revision
AUTOMATIC TRANSAXLE
23A-398
(3) Position special tool MB991527 and MB991454 (chain) to
hold the engine/transaxle assembly.
NOTE: Adjust the engine hanger balance by sliding the
slide bracket (HI).
INSTALLATION SERVICE POINT
.
>>A<< TRANSAXLE ASSEMBLY INSTALLATION
Engage the torque converter into the transaxle side securely,
and then assemble the transaxle assembly on the engine.
.
>>B<< TRANSAXLE MOUNT STOPPER INSTALLATION
Install the transaxle mount stopper so that its arrow points
upward.
.
>>C<< DRIVE SHAFT/DRIVE SHAFT AND INNER SHAFT
ASSEMBLY INSTALLATION
CAUTION
When installing the drive shaft or the drive shaft and inner
shaft assembly, be careful that the spline part of the drive
shaft or the drive shaft and inner shaft assembly do not
damage the oil seal.
.
AC306200
AB
MB991928
MB991527
MB991454
AC209056
APPROXIMATELY
12.2 mm (0.48 in)
AD
TORQUE
CONVERTER
AC205424
ENGINE SIDE
TRANSAXLE
MOUNT
STOPPER
TRANSAXLE
MOUNT
AB
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст