Mitsubishi Galant (2004+). Manual — part 712

TRANSAXLE ASSEMBLY

TSB Revision

AUTOMATIC TRANSAXLE

23A-399

>>D<< DRIVE SHAFT NUT INSTALLATION
1. Be sure to install the drive shaft washer in the specified

direction.

CAUTION

Before securely tightening the drive shaft nuts, make sure
there is no load on the wheel bearings. Otherwise the
wheel bearing will be damaged.
2. Using special tool MB990767, tighten the drive shaft nut to

the specified torque.

Tightening torque: 226

± 29 N⋅m (167 ± 21 ft-lb)

.

>>E<< ADJUSTING NUT/TRANSAXLE CONTROL CABLE
(TRANSAXLE SIDE) INSTALLATION
1. Place the selector lever and manual control lever in the “N”

position.

2. Place the cable stud into the manual control lever slot and

install the nut loosely. Gently push the transaxle control
cable into the manual control lever slot until the cable is taut.
Tighten the nut to the specified torque.

Tightening torque: 12

± 2 N⋅m (107 ± 17 in-lb)

AC210244AB

MB990767

WASHER

AC305532

12 ± 2 N·m
107 ± 17 in-lb

MANUAL CONTROL LEVER

ADJUSTING NUT

AE

TRANSAXLE ASSEMBLY

TSB Revision

AUTOMATIC TRANSAXLE

23A-400

REMOVAL AND INSTALLATION

M1231005700459

<F4A5A>

CAUTION

*

: Indicates parts which should be temporarily tightened, and then fully tightened after placing the

vehicle horizontally and loading the full weight of the engine on the vehicle body.

Pre-installation Operation
• Front Under Cover, Side Under Cover Removal
• Transmission Fluid Draining (Refer to GROUP 00, Main-

tenance Service

− Automatic Transaxle

P.00-50

.)

• Engine Cover Removal (Refer to GROUP 11C, Engine

Assembly

P.11C-15

.)

• Air Cleaner Assembly Removal (Refer to GROUP 15, Air

Cleaner

P.15-4

.)

• Powertrain Control Module (PCM) Removal (Refer to

GROUP 13A

P.13A-1121

.)

• Battery and Battery Tray Removal
• Front Exhaust Pipe Removal (Refer to GROUP 15,

Exhaust Pipe and Main Muffler

P.15-21

.)

Post-installation Operation
• Front Exhaust Pipe Installation (Refer to GROUP 15,

Exhaust Pipe and Main Muffler

P.15-21

.)

• Battery and Battery Tray Installation
• Powertrain Control Module (PCM) Installation (Refer to

GROUP 13A

P.13A-1121

.)

• Air Cleaner Assembly Installation (Refer to GROUP 15,

Air Cleaner

P.15-4

.)

• Engine Cover Installation (Refer to GROUP 11C, Engine

Assembly

P.11C-15

.)

• Transmission Fluid Supplying (Refer to GROUP 00, Main-

tenance Service

− Automatic Transaxle

P.00-50

.)

• Front Under Cover, Side Under Cover Installation

• Selector Lever Operation Check (Refer to

P.23A-381

.)

• Speedometer Operation Check (Refer to GROUP 54A,

Combination Meter

− On-vehicle Service − Speedometer

Check

P.54A-106

.)

• Front Wheel Alignment Check and Adjustment (Refer to

GROUP 33, On-vehicle Service

− Front Wheel Alignment

Check and Adjustment

P.33-6

.)

AC305969

7

N

8

226 ± 29 N·m
167 ± 21 ft-lb

65 ± 6 N·m
48 ± 4 ft-lb

12

N

48 ± 7 N·m
36 ± 5 ft-lb

10

9

48 ± 7 N·m
36 ± 5 ft-lb

N

14

16

19

2

1

12 ± 2 N·m
107 ± 17 in-lb

73 ± 10 N·m
54 ± 7 ft-lb

3

4

5

6

22

30 ± 3 N·m
23 ± 2 ft-lb

30 ± 3 N·m
22 ± 2 ft-lb

41 ± 4 N·m
30 ± 3 ft-lb

N

17

19

AB

23

23

73 ± 10 N·m
54 ± 7 ft-lb

13

15

18

21

21

11

REMOVAL STEPS

>>E<<

1.

ADJUSTING NUT

>>E<<

2.

TRANSAXLE CONTROL CABLE
CONNECTION

3.

INHIBITOR SWITCH SENSOR
CONNECTOR

REMOVAL STEPS (Continued)

TRANSAXLE ASSEMBLY

TSB Revision

AUTOMATIC TRANSAXLE

23A-401

4.

A/T CONTROL SOLENOID VALVE
ASSEMBLY CONNECTOR

5.

INPUT SHAFT SPEED SENSOR
CONNECTOR

6.

OUTPUT SHAFT SPEED
SENSOR CONNECTOR

7.

SPLIT PIN

<<A>>

>>D<<

8.

DRIVE SHAFT NUT

9.

WHEEL SPEED SENSOR

10. WHEEL SPEED SENSOR

BRACKET

11. BRAKE HOSE CLAMP
12. STABILIZER LINK CONNECTION

<STRUT SIDE>

13. SELF-LOCKING NUT

(CONNECTION FOR TIE ROD
END)

<<B>>

14. TIE ROD END CONNECTION
15. SELF-LOCKING NUT

(CONNECTION FOR LOWER
ARM BALL JOINT)

<<B>>

16. LOWER ARM BALL JOINT

CONNECTION

<<C>>

>>C<<

17. DRIVE SHAFT <LH>
18. CIRCLIP

<<C>>

>>C<<

19. DRIVE SHAFT AND INNER

SHAFT ASSEMBLY <RH>

20. TRANSMISSION FLUID COOLER

HOSE

21. STARTER MOTOR INSTALLATION

BOLTS

22. STARTER MOTOR
23. TRANSAXLE ASSEMBLY UPPER

PART COUPLING BOLTS

REMOVAL STEPS (Continued)

TRANSAXLE ASSEMBLY

TSB Revision

AUTOMATIC TRANSAXLE

23A-402

Required Special Tools:

• MB990767: End Yoke Holder

• MB991897: Ball Joint Remover

• MB990242: Puller Shaft Puller

• MB990244: Puller Bar

• MB991354: Puller Body

• MB990998: Front Hub Remover and Installer

• MB991000: Spacer

• MB991454: Engine Hanger Balancer

• MB991895: Engine Hanger

• MB991928: Engine Hanger

• MB991932: Foot (standard)

• MB991929: Joint (50)

• MB991931: Joint (140)

AC305970

83 ± 12 N·m
61 ± 9 ft-lb

83 ± 12 N·m
61 ± 9 ft-lb

58 ± 7 N·m*
43 ± 5 ft-lb*

26

90 ± 10 N·m
67 ± 7 ft-lb

58 ± 7 N·m*
43 ± 5 ft-lb*

11 ± 0.5 N·m
93 ± 4 in-lb

49 ± 3 N·m
36 ± 2 ft-lb

25

24

32

88 ± 10 N·m
65 ± 7 ft-lb

58 ± 7 N·m*
43 ± 5 ft-lb*

83 ± 12 N·m*
61 ± 9 ft-lb*

30

30

31

29

28

33

AB

27

35 ± 6 N·m
26 ± 4 ft-lb

REMOVAL STEPS

24. COVER

<<D>>

25. TORQUE CONVERTER AND

DRIVE PLATE BOLTS

26. CENTERMEMBER ASSEMBLY
27. ENGINE OIL PAN AND

TRANSAXLE COUPLING BOLTS

28. REAR ROLL STOPPER BRACKET
•

AIR CLEANER BRACKET

29. TRANSAXLE MOUNT BRACKET

ASSEMBLY

>>B<<

30. TRANSAXLE MOUNT STOPPER
31. TRANSAXLE MOUNT BRACKET

<<E>>

•

ENGINE ASSEMBLY SUPPORT

•

LIFTING UP OF THE VEHICLE

•

SUPPORT THE TRANSAXLE
WITH A TRANSAXLE JACK

32. TRANSAXLE ASSEMBLY LOWER

PART COUPLING BOLTS

>>A<<

33. TRANSAXLE ASSEMBLY

REMOVAL STEPS (Continued)