Mitsubishi Galant (2004+). Manual — part 396
DIAGNOSIS
TSB Revision
CONTROLLER AREA NETWORK (CAN)
54C-195
STEP 23. Check the CAN_H line (communication line only)
between intermediate connector and the powertrain
control module connector for short to ground. Measure the
resistance at intermediate connector C-29.
CAUTION
A digital multimeter should be used. For details refer to
CAUTION
The test wiring harness should be used. For details refer to
(1) Disconnect intermediate connector C-29 and powertrain
control module connector B-19, and measure the resistance
at the wiring male side of intermediate connector C-29.
(2) Turn the ignition switch to the "LOCK" (OFF) position.
CAUTION
Disconnect the negative battery terminal. For details refer
to
.
(3) Disconnect the negative battery terminal.
AC306248AD
B-19 (B)
CONNECTOR: B-19
PCM
AIR
CLEANER
HARNESS SIDE
AC305231AI
CONNECTOR: C-29
DIAGNOSIS
TSB Revision
CONTROLLER AREA NETWORK (CAN)
54C-196
(4) Measure the resistance between intermediate connector
terminal 11 and body ground.
OK: 1 k
Ω or more
CAUTION
Strictly observe the specified wiring harness repair proce-
dure. For details refer to
Q: Does the resistance measure 1 k
Ω or more?
YES : If the resistance measures 1 k
Ω or more, diagnose
CAN bus lines thoroughly by referring to
NO : If the resistance measures less than 1 k
Ω, repair the
wiring harness between intermediate connector and
the powertrain control module connector.
STEP 24. Check intermediate connector C-29 for loose,
corroded or damaged terminals, or terminals pushed back
in the connector.
CAUTION
The strand end of the twisted wire should be within 10 cm
(4 inches) from the connector. For details refer to
Q: Is intermediate connector C-29 in good condition?
YES : Go to Step 25.
NO : Repair the damaged parts.
AC209364
2 3
27
32
28
33
16
15
4 5
19
18
29
17
34
7 8
35
22
21
9 10
30
36
31
37
25
24
23
6
20
1
14
26
11
13
12
38
AC209364
MALE SIDE: C-29
TEST
HARNESS
HV
AC305231AI
CONNECTOR: C-29
DIAGNOSIS
TSB Revision
CONTROLLER AREA NETWORK (CAN)
54C-197
STEP 25. Check the CAN_L-side bus line (communication
line including ECUs) of the front wiring harness for short
to ground. Measure the resistance at intermediate
connector C-29.
CAUTION
A digital multimeter should be used. For details refer to
CAUTION
The test wiring harness should be used. For details refer to
(1) Disconnect intermediate connector C-29, and measure the
resistance at the male side (at front wiring harness side).
(2) Turn the ignition switch to the "LOCK" (OFF) position.
CAUTION
Disconnect the negative battery terminal. For details refer
to
.
(3) Disconnect the negative battery terminal.
(4) Measure the resistance between intermediate connector
terminal 12 and body ground.
OK: 1 k
Ω or more
Q: Does the resistance measure 1 k
Ω or more?
YES : If the resistance measures 1 k
Ω or more, go to Step
26 .
NO : If the resistance measures less than 1 k
Ω, go to Step
43 .
AC305231AI
CONNECTOR: C-29
AC209364
2 3
27
32
28
33
16
15
4 5
19
18
29
17
34
7 8
35
22
21
9 10
30
36
31
37
25
24
23
6
20
1
14
26
11
13
12
38
MALE SIDE: C-29
TEST HARNESS
GA
DIAGNOSIS
TSB Revision
CONTROLLER AREA NETWORK (CAN)
54C-198
STEP 26. Check joint connector (3) C-02 for loose,
corroded or damaged terminals, or terminals pushed back
in the connector.
CAUTION
The strand end of the twisted wire should be within 10 cm
(4 inches) from the connector. For details refer to
Check the joint connector at the wiring harness side for loose,
corroded or damaged terminals, or terminals pushed back in
the connector, and also check the short pin behind the connec-
tor for corrosion, deformation and delamination.
Q: Is joint connector (3) C-02 in good condition?
YES : Go to Step 27.
NO : Repair the damaged parts. Replace the joint
connector as necessary.
AC305231AP
CONNECTOR: C-02
AC209350
1
12
2
13
3
14
4
15
5
16
6
17
7
18
8
19
9
20
10
21
11
22
AB
SHORT PIN
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст