Mitsubishi Galant (2004+). Manual — part 956
MULTIPORT FUEL INJECTION (MFI) DIAGNOSIS
TSB Revision
MULTIPORT FUEL INJECTION (MFI) <2.4L ENGINE>
13A-641
STEP 8. Check for open circuit and short circuit to ground
between evaporative emission ventilation solenoid
connector F-08 (terminal No. 1) and PCM connector B-19
(terminal No. 11).
NOTE: Check harness after checking intermediate connector
C-25. If intermediate connector is damaged, repair or replace it.
Refer to GROUP 00E, Harness Connector Inspection
Then go to Step 12.
Q: Is the harness wire in good condition?
YES : Replace the PCM. Then go to Step 12.
NO : Repair it. Then go to Step 12.
AK303873
1
2
AB
CONNECTOR: F-08
F-08 (B)
HARNESS
CONNECTOR:
COMPONENT SIDE
AK303153
4 3 2 1
7 6 5
9 8
11 10
14 13 12
18 17 16 15
CONNECTOR: B-19
PCM
AB
AIR CLEANER
HARNESS CONNECTOR:
COMPONENT SIDE
B-19 (B)
MULTIPORT FUEL INJECTION (MFI) DIAGNOSIS
TSB Revision
MULTIPORT FUEL INJECTION (MFI) <2.4L ENGINE>
13A-642
STEP 9. Check harness connector B-19 at PCM for
damage.
Q: Is the harness connector in good condition?
YES : Go to Step 10.
NO : Repair or replace it. Refer to GROUP 00E, Harness
Connector Inspection
. Then go to Step 12.
STEP 10. Check for harness damage between MFI relay
connector B-17X (terminal No. 4) and evaporative emission
ventilation solenoid connector F-08 (terminal No. 2).
AK303153
4 3 2 1
7 6 5
9 8
11 10
14 13 12
18 17 16 15
CONNECTOR: B-19
PCM
AB
AIR CLEANER
HARNESS CONNECTOR:
COMPONENT SIDE
B-19 (B)
AK303806
2
1
3
4
AB
CONNECTOR: B-17X
B-17X
RELAY BOX
TRIANGLE
MARK
HARNESS CONNECTOR:
COMPONENT SIDE
AK303873
1
2
AB
CONNECTOR: F-08
F-08 (B)
HARNESS
CONNECTOR:
COMPONENT SIDE
MULTIPORT FUEL INJECTION (MFI) DIAGNOSIS
TSB Revision
MULTIPORT FUEL INJECTION (MFI) <2.4L ENGINE>
13A-643
NOTE: Check harness after checking intermediate connectors
A-13 and C-25. If intermediate connectors are damaged, repair
or replace them. Refer to GROUP 00E, Harness Connector
Inspection
. Then go to Step 12.
Q: Is the harness wire in good condition?
YES : Go to Step 11.
NO : Repair it. Then go to Step 12.
STEP 11. Check for harness damage between evaporative
emission ventilation solenoid connector F-08 (terminal No.
1) and PCM connector B-19 (terminal No. 2).
NOTE: Check harness after checking intermediate connector
C-25. If intermediate connector is damaged, repair or replace it.
Refer to GROUP 00E, Harness Connector Inspection
Then go to Step 12.
Q: Is the harness wire in good condition?
YES : Replace the PCM. Then go to Step 12.
NO : Repair it. Then go to Step 12.
AK303873
1
2
AB
CONNECTOR: F-08
F-08 (B)
HARNESS
CONNECTOR:
COMPONENT SIDE
AK303153
4 3 2 1
7 6 5
9 8
11 10
14 13 12
18 17 16 15
CONNECTOR: B-19
PCM
AB
AIR CLEANER
HARNESS CONNECTOR:
COMPONENT SIDE
B-19 (B)
MULTIPORT FUEL INJECTION (MFI) DIAGNOSIS
TSB Revision
MULTIPORT FUEL INJECTION (MFI) <2.4L ENGINE>
13A-644
STEP 12. Test the OBD-II drive cycle.
(1) Carry out a test drive with the drive cycle pattern. Refer to
Diagnostic Function
− OBD-II Drive Cycle − Procedure 6 −
Other Monitor
(2) Check the diagnostic trouble code (DTC).
Q: Is DTC P0446 set?
YES : Retry the troubleshooting.
NO : The inspection is complete.
DTC P0451: Evaporative Emission System Pressure Sensor Range/Performance
AC306277
A
B
C
D
E
F
G
H
P
Q
R
O
N
M
I
J
K
L
AC
INTAKE MANIFOLD
FUEL TANK
EVAPORATIVE EMISSION
VENTILATION SOLENOID
CHECK VALVE
EVAPORATIVE EMISSION
PURGE SOLENOID
EVAPORATIVE
EMISSION CANISTER
ONBOARD REFUELING
VAPOR RECOVERY(ORVR)
VENT VALVE MODULE
FUEL TANK DIFFERENTIAL
PRESSURE SENSOR
SYSTEM DIAGRAM
CHAMBER
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст