Mitsubishi Galant 9G. Manual — part 754
MULTIPORT FUEL INJECTION (MFI) DIAGNOSIS
TSB Revision
MULTIPORT FUEL INJECTION (MFI) <2.4L ENGINE>
13A-458
STEP 3. Check the fuel tank temperature sensor.
(1) Disconnect the fuel tank temperature sensor connector
D-18.
(2) Measure the resistance between terminal No. 1 and No. 3
of the fuel tank temperature sensor.
Standard value:
0.5
− 12.0 kΩ
Q: Is the measured resistance between 0.5 and 12.0 k
Ω?
YES : Go to Step 4.
NO : Replace the fuel tank temperature sensor. Then go to
Step 11.
STEP 4. Check the sensor supply voltage at fuel tank
temperature sensor harness side connector D-18.
(1) Disconnect the connector D-18 and measure at the harness
side.
(2) Turn the ignition switch to the "ON" position.
(3) Measure the voltage between terminal No. 3 and ground.
• Voltage should be between 4.5 and 4.9 volts.
(4) Turn the ignition switch to the "LOCK" (OFF) position.
Q: Is the measured voltage between 4.5 and 4.9 volts?
YES : Go to Step 8.
NO : Go to Step 5.
AK303840
1
2
3
4
5
SERVICE
HOLE
AB
CONNECTOR: D-18
D-18 (GR)
HARNESS
CONNECTOR:
COMPONENT SIDE
1
2 3
4
5
AK203165
FUEL TANK TEMPERATURE
SENSOR CONNECTOR
AB
AK303840
1
2
3
4
5
SERVICE
HOLE
AB
CONNECTOR: D-18
D-18 (GR)
HARNESS
CONNECTOR:
COMPONENT SIDE
1
2
3
4
5
AK203167
D-18 HARNESS
CONNECTOR:
COMPONENT SIDE
AC
MULTIPORT FUEL INJECTION (MFI) DIAGNOSIS
TSB Revision
MULTIPORT FUEL INJECTION (MFI) <2.4L ENGINE>
13A-459
STEP 5. Check the sensor supply voltage at PCM
connector B-20 by using power plant ECU check harness
special tool MB991923.
(1) Disconnect the all PCM connectors and connect power
plant ECU check harness special tool MB991923 between
the separated connectors.
(2) Disconnect the fuel tank temperature sensor connector
D-18.
(3) Turn the ignition switch to the "ON" position.
AK303092
25
21
24 23 22
29 28 27 26
34 33 32 31 30
38 37 36 35
43 42 41 40 39
CONNECTOR: B-20
B-20
PCM
AB
HARNESS CONNECTOR:
COMPONENT SIDE
AIR CLEANER
AK203002
25
21
24 23 22
29 28 27 26
34 33 32 31 30
38 37 36 35
43 42 41 40 39
AB
POWER PLANT ECU
CHECK HARNESS CONNECTOR
MB991923
PCM
MULTIPORT FUEL INJECTION (MFI) DIAGNOSIS
TSB Revision
MULTIPORT FUEL INJECTION (MFI) <2.4L ENGINE>
13A-460
(4) Measure the voltage between terminal No. 41 and ground.
• Voltage should be between 4.5 and 4.9 volts.
(5) Turn the ignition switch to the "LOCK" (OFF) position.
Q: Is the measured voltage between 4.5 and 4.9 volts?
YES : Go to Step 6.
NO : Go to Step 7.
STEP 6. Check harness connector B-20 at PCM for
damage.
Q: Is the harness connector in good condition?
YES : Check harness connector C-25 at intermediate
connector for damage, and repair or replace as
required. Refer to GROUP 00E, Harness Connector
Inspection
. If the intermediate connector is in
good condition, repair the harness wire between fuel
tank temperature sensor connector D-18 and PCM
connector B-20 because of open circuit. Then go to
Step 11.
NO : Repair or replace it. Refer to GROUP 00E, Harness
. Then go to Step 11.
25
21
24 23 22
29 28 27 26
34 33 32 31 30
38 37 36 35
43 42 41 40 39
AK203168AB
POWER PLANT ECU
CHECK HARNESS
CONNECTOR
AK303092
25
21
24 23 22
29 28 27 26
34 33 32 31 30
38 37 36 35
43 42 41 40 39
CONNECTOR: B-20
B-20
PCM
AB
HARNESS CONNECTOR:
COMPONENT SIDE
AIR CLEANER
MULTIPORT FUEL INJECTION (MFI) DIAGNOSIS
TSB Revision
MULTIPORT FUEL INJECTION (MFI) <2.4L ENGINE>
13A-461
STEP 7. Check harness connector B-20 at PCM for
damage.
Q: Is the harness connector in good condition?
YES : Replace the PCM. Then go to Step 11.
NO : Repair or replace it. Refer to GROUP 00E, Harness
. Then go to Step 11.
STEP 8. Check the continuity at fuel tank temperature
sensor harness side connector D-18.
(1) Disconnect the connector D-18 and measure at the harness
side.
(2) Check for the continuity between terminal No. 1 and
ground.
• Should be less than 2 ohms.
Q: Does continuity exist?
YES : Go to Step 9.
NO : Repair harness wire between fuel tank temperature
sensor connector D-18 (terminal No. 1) and ground
because of open circuit or harness damage. Then go
to Step 11.
AK303092
25
21
24 23 22
29 28 27 26
34 33 32 31 30
38 37 36 35
43 42 41 40 39
CONNECTOR: B-20
B-20
PCM
AB
HARNESS CONNECTOR:
COMPONENT SIDE
AIR CLEANER
AK303840
1
2
3
4
5
SERVICE
HOLE
AB
CONNECTOR: D-18
D-18 (GR)
HARNESS
CONNECTOR:
COMPONENT SIDE
1
2
3
4
5
AK203166
D-18 HARNESS
CONNECTOR:
COMPONENT SIDE
AC
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст