Mitsubishi Galant 9G. Manual — part 788
MULTIPORT FUEL INJECTION (MFI) DIAGNOSIS
TSB Revision
MULTIPORT FUEL INJECTION (MFI) <2.4L ENGINE>
13A-594
STEP 8. Check harness connector B-23 at PCM for
damage.
Q: Is the harness connector in good condition?
YES : Go to Step 9.
NO : Repair or replace it. Refer to GROUP 00E, Harness
. Then go to Step 12.
127 126 125 124 123 122 121
133 132 131 130 129 128
140 139 138 137 136 135 134
146 145 144 143 142 141
153 152 151 150 149 148 147
AK303058
HARNESS CONNECTOR:
COMPONENT SIDE
CONNECTOR: B-23
B-23
PCM
AB
AIR CLEANER
MULTIPORT FUEL INJECTION (MFI) DIAGNOSIS
TSB Revision
MULTIPORT FUEL INJECTION (MFI) <2.4L ENGINE>
13A-595
STEP 9. Check the EGR valve operation using special tool
MB991658.
(1) Remove the EGR valve.
(2) Connect special tool MB991658 to the EGR valve. (All
terminals should be connected.)
(3) Use the jumper wires to connect terminal No. 5 of the EGR
valve connector to the positive battery terminal.
(4) Check to ensure that the motor operates when the terminal
No. 1 and No. 3 of the EGR valve connector are
respectively connected to the negative battery terminal
using a jumper wire.
• Vibration should be present at each application of volt-
age to test clip combination.
(5) Then, use jumper wires to connect the terminal No. 2 of the
EGR valve connector to the positive battery terminal.
(6) Check to ensure that the motor operates when terminal No.
4 and No. 6 of the EGR valve connector are respectively
connected to the negative battery terminal using a jumper
wire.
• Vibration should be present at each application of volt-
age to test clip combination.
(7) Reinstall the EGR valve, using a new gasket, and tighten to
the specified torque.
Tighten torque: 24
± 3 N⋅m [17 ± 3 ft⋅Ib]
Q: Is the EGR valve operating properly?
YES : Go to Step 10.
NO : Replace the EGR valve. Then go to Step 12.
AK303866
1
2
3
4
5
6
AB
CONNECTOR: B-105
B-105 (GR)
HARNESS CONNECTOR:
COMPONENT SIDE
AK203699
+
-
AB
BATTERY
MB991658
MULTIPORT FUEL INJECTION (MFI) DIAGNOSIS
TSB Revision
MULTIPORT FUEL INJECTION (MFI) <2.4L ENGINE>
13A-596
STEP 10. Check for harness damage between MFI relay
connector B-17X (terminal No. 4) and EGR valve connector
B-105 (terminal No. 2, No. 5).
Q: Is the harness wire in good condition?
YES : Go to Step 11.
NO : Repair it. Then go to Step 12.
AK303806
2
1
3
4
AB
CONNECTOR: B-17X
B-17X
RELAY BOX
TRIANGLE
MARK
HARNESS CONNECTOR:
COMPONENT SIDE
AK303866
1
2
3
4
5
6
AB
CONNECTOR: B-105
B-105 (GR)
HARNESS CONNECTOR:
COMPONENT SIDE
MULTIPORT FUEL INJECTION (MFI) DIAGNOSIS
TSB Revision
MULTIPORT FUEL INJECTION (MFI) <2.4L ENGINE>
13A-597
STEP 11. Check for harness damage between EGR valve
connector B-105 and PCM connector B-23.
a. EGR valve connector B-105 (terminal No. 1) and PCM con-
nector B-23 (terminal No. 142).
b. EGR valve connector B-105 (terminal No. 3) and PCM con-
nector B-23 (terminal No. 136).
c. EGR valve connector B-105 (terminal No. 4) and PCM con-
nector B-23 (terminal No. 130).
d. EGR valve connector B-105 (terminal No. 6) and PCM con-
nector B-23 (terminal No. 124).
Q: Is the harness wire in good condition?
YES : Replace the PCM. Then go to Step 12.
NO : Repair it. Then go to Step 12.
STEP 12. Test the OBD-II drive cycle.
(1) Carry out a test drive with the drive cycle pattern. Refer to
Diagnostic Function
− OBD-II Drive Cycle − Procedure 6 −
(2) Check the diagnostic trouble code (DTC).
Q: Is DTC P0403 set?
YES : Retry the troubleshooting.
NO : The inspection is complete.
AK303866
1
2
3
4
5
6
AB
CONNECTOR: B-105
B-105 (GR)
HARNESS CONNECTOR:
COMPONENT SIDE
127 126 125 124 123 122 121
133 132 131 130 129 128
140 139 138 137 136 135 134
146 145 144 143 142 141
153 152 151 150 149 148 147
AK303058
HARNESS CONNECTOR:
COMPONENT SIDE
CONNECTOR: B-23
B-23
PCM
AB
AIR CLEANER
NEXT>>
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст