Mitsubishi Galant 9G. Manual — part 858
MULTIPORT FUEL INJECTION (MFI) DIAGNOSIS
TSB Revision
MULTIPORT FUEL INJECTION (MFI) <2.4L ENGINE>
13A-874
DTC P2066: Fuel Level Sensor (sub) Circuit Range/Performance
1
2 3
4
5
22
21
23 24 25
26 27 28 29
30 31 32 33 34
35 36 37 38
39 40 41 42 43
1
2
AK400894
Fuel Level Sensor Circuit
FUEL LEVEL
SENSOR (SUB)
FUEL LEVEL SENSOR (MAIN)
(INTEGRATED IN FUEL PUMP MODULE)
13
2
1
2
1
11
PINK-
BLA
CK
BLA
CK
PINK-
BLACK
PINK-
BLA
CK
PINK-BLA
CK
24
GRA
Y
GRA
Y
POWERTRAIN
CONTROL
MODULE (PCM)
C-28
C-25
D-18
(MU802058)
D-17
CONBINATION METER
B-20
AK303875AB
CONNECTOR: D-17
FUEL LEVEL
SENSOR (SUB)
D-17
SERVICE
HOLE
AK303876AB
CONNECTOR: D-18
SERVICE
HOLE
FUEL LEVEL SENSOR (MAIN)
(INTEGRATED IN FUEL PUMP MODULE)
D-18 (GR)
MULTIPORT FUEL INJECTION (MFI) DIAGNOSIS
TSB Revision
MULTIPORT FUEL INJECTION (MFI) <2.4L ENGINE>
13A-875
.
CIRCUIT OPERATION
• The fuel level sensor (sub) drive signal is input in
combination meter (terminal No. 13).
.
TECHNICAL DESCRIPTION
• Branch the drive signal from the fuel level sensor
circuit, and input it into combination meter.
• The combination meter detects the amount of
fuel left in the fuel tank with this signal, and also
controls the fuel level warning light.
.
DESCRIPTIONS OF MONITOR METHODS
Detect malfunction if change of fuel level sensor out-
put voltage is small when sum of fuel injection is
large.
.
MONITOR EXECUTION
Continuous
.
MONITOR EXECUTION CONDITIONS
(Other monitor and Sensor)
Other Monitor (There is no temporary DTC stored
in memory for the item monitored below)
• Not applicable
Sensor (The sensor below is determined to be
normal)
• Not applicable
.
AK303838AB
C-25
CONNECTOR: C-25
AK303085
CONNECTOR: B-20
PCM
AB
AIR CLEANER
B-20
AK303877AB
C-28
CONNECTOR: C-28
MULTIPORT FUEL INJECTION (MFI) DIAGNOSIS
TSB Revision
MULTIPORT FUEL INJECTION (MFI) <2.4L ENGINE>
13A-876
DTC SET CONDITIONS
Logic Flow Chart
.
INDICATED
FUEL LEVEL CHANGE
< 2L (0.5gal)
ACCUMULATE FUEL CONSUMPTION
THROUGH FUEL INJECTORS.
ACCUMULATED FUEL
CONSUMPTION WILL NOT
RESET WHEN KEY-OFF/ON.
ACCUMULATED
FUEL CONSUMPTION
> =SPECIFIED VALVE
START
END
NO
NO
NO
YES
YES
YES
MALFUNCTION
GOOD
MONITORING
CONDITIONS
RESET ACCUMULATE
FUEL CONSUMPTION.
AK302040
MULTIPORT FUEL INJECTION (MFI) DIAGNOSIS
TSB Revision
MULTIPORT FUEL INJECTION (MFI) <2.4L ENGINE>
13A-877
Check Conditions, Judgement Criteria
• When the fuel consumption calculated from the
operation time of the injector amounts to 30 liters
(7.9 gal), the diversity of the amount of fuel in
tank calculated from the fuel level sensor is 2
liters (0.5 gal) or less.
.
OBD-II DRIVE CYCLE PATTERN
Refer to Diagnostic Function
− OBD-II Drive Cycle −
Procedure 6
.
.
TROUBLESHOOTING HINTS (The most
likely causes for this code to be set are:)
• Fuel pump module or fuel level sensor (sub)
failed.
• PCM failed.
DIAGNOSIS
Required Special Tools:
• MB991958: Scan tool (MUT-III Sub Assembly)
• MB991824: V.C.I.
• MB991827: USB Cable
• MB991910: Main Harness A
STEP 1. Using scan tool MB991958, read the diagnostic
trouble code (DTC).
CAUTION
To prevent damage to scan tool MB991958, always turn the
ignition switch to the "LOCK" (OFF) position before con-
necting or disconnecting scan tool MB991958.
(1) Connect scan tool MB991958 to the data link connector.
(2) Turn the ignition switch to the "ON" position.
(3) Read the DTC.
(4) Turn the ignition switch to the "LOCK" (OFF) position.
Q: Is DTC P0461 set?
YES : Go to Step 2.
NO : Go to Step 4.
STEP 2. Check fuel gauge.
Q: Is the fuel gauge functioning?
YES : Go to Step 3.
NO : Refer to GROUP 54A, Chassis Electrical
−
Combination Meters Assembly and Vehicle Speed
Sensor
− Symptom Chart
AK303804AB
MB991910
DATA LINK
CONNECTOR
MB991824
MB991827
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст