Mitsubishi Galant 9G. Manual — part 1550
COMBINATION METER ASSEMBLY
TSB Revision
CHASSIS ELECTRICAL
54A-72
STEP 1. Using scan tool MB991958, diagnose the CAN bus
line.
Use scan tool MB991958 to diagnose the CAN bus lines.
(1) Connect scan tool MB991958 to the data link connector.
(2) Turn the ignition switch to "ON" position.
(3) Diagnose the CAN bus line.
Q: Is the check result satisfactory?
YES : Go to Step 2.
NO : Repair the CAN bus lines (Refer to GROUP 54C,
Diagnosis-Can Bus Diagnostic Chart
). On
completion, go to Step 4.
STEP 2. Using scan tool MB991958, read the ETACS-ECU
diagnostic trouble code.
Check that the ETACS-ECU sets a DTC.
Q: Is the DTC set?
YES : Diagnose the SWS system by referring to
.
NO : Go to Step 3.
STEP 3. Replace the ETACS-ECU and then recheck the
DTC.
Replace the ETACS-ECU, and then check that the DTC is not
reset.
Q: Is the check result satisfactory?
YES : Go to Step 4.
NO : Replace combination meter and then go to step 4.
STEP 4. Recheck for diagnostic trouble code.
Recheck if the DTC is set.
1. Erase the DTC.
2. Turn the ignition switch to "ON" position.
3. Check if the DTC is set.
Q: Is the check result satisfactory?
YES : The procedure is complete.
NO : Go to Step 1.
AC305412
AB
MB991910
DATA LINK
CONNECTOR
MB991824
MB991827
COMBINATION METER ASSEMBLY
TSB Revision
CHASSIS ELECTRICAL
54A-73
SYMPTOM CHART
M1543007201116
CAUTION
During diagnosis, a DTC code associated with
other system may be set when the ignition switch
is turned on with connector(s) disconnected. On
completion, confirm all systems for DTC code(s).
If DTC code(s) are set, erase them all.
SYMPTOM
INSPECTION
PROCEDURE
REFERENCE PAGE
Communication with scan tool is not possible.
1
Power supply circuit.
2
Odometer and trip meter are not displayed.
3
All the needle meters do not work.
4
When the ignition switch is turned to the ON position, the
indicator and warning lights do not illuminate.
5
Speedometer does not work.
6
The fuel gauge needle moves excessively.
7
Tachometer does not work.
8
Fuel Gauge does not work (other meters work).
9
Engine coolant temperature gauge does not work (other meters
work).
10
COMBINATION METER ASSEMBLY
TSB Revision
CHASSIS ELECTRICAL
54A-74
SYMPTOM PROCEDURES
INSPECTION PROCEDURE 1:Communication With Scan Tool is Not Possible.
WITHOUT ELECTRONIC
BRAKE-FORCE
DISTRIBUTION (EBD)
AND ANTI-LOCK
BRAKING SYSTEM
(ABS)
WITHOUT ELECTRONIC
BRAKE-FORCE
DISTRIBUTION (EBD)
AND ANTI-LOCK
BRAKING SYSTEM
(ABS)
WITH ELECTRONIC
BRAKE-FORCE
DISTRIBUTION (EBD)
AND ANTI-LOCK
BRAKING SYSTEM
(ABS)
WITH ELECTRONIC
BRAKE-FORCE
DISTRIBUTION (EBD)
AND ANTI-LOCK
BRAKING SYSTEM
(ABS)
ABS-ECU OR ABS/TCL-ECU
JOINT
CONNECTOR (3)
POWERTRAIN
CONTROL
MODULE
COMBINATION
METER
CPU
DATA LINK CONNECTOR
Combinaton Meter CAN-BUS Line Circuit
COMBINATION METER ASSEMBLY
TSB Revision
CHASSIS ELECTRICAL
54A-75
.
CIRCUIT OPERATION
The combination meter is linked to the data link con-
nector via CAN bus line to communicate with the
scan tool.
.
TECHNICAL DESCRIPTION (COMMENT)
If the system does not communicate with scan tool,
power supply to data link connector or CAN bus lines
may be defective.
.
TROUBLESHOOTING HINTS
• The wiring harness or connectors may have
loose, corroded, or damaged terminals, or termi-
nals pushed back in the connector.
AC305206
CONNECTOR: A-02
AO
A-02 (GR)
AC305216
B-19 (B)
CONNECTOR: B-19
AD
AC305231
C-02
C-29
C-101
C-125 (B)
DC
CONNECTORS: C-02, C-29, C-101, C-125
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст