Mitsubishi Galant 9G. Manual — part 1219
ON-VEHICLE SERVICE
TSB Revision
MULTIPORT FUEL INJECTION (MFI) <3.8L ENGINE>
13B-1176
AK302286
I
CRANKSHAFT
POSITION SENSOR
CONNECTOR
CRANKSHAFT
POSITION
SENSOR
AB
CRANKSHAFT
SPROCKET
AK303261AB
INJECTOR
J
AK303288
KNOCK SENSOR
CONNECTOR
KNOCK SENSOR
AB
K
AK303279
IGNITION COIL
AB
L
ON-VEHICLE SERVICE
TSB Revision
MULTIPORT FUEL INJECTION (MFI) <3.8L ENGINE>
13B-1177
AK303299AB
M
LEFT BANK
HEATED OXYGEN
SENSOR (FRONT)
CONNECTOR
LEFT BANK
HEATED OXYGEN
SENSOR (REAR)
CONNECTOR
LEFT BANK
HEATED OXYGEN
SENSOR (FRONT)
LEFT BANK
HEATED OXYGEN
SENSOR (REAR)
AK303303
N
CAMSHAFT POSITION
SENSOR
AB
AK303306
PCM
AIR CLEANER
AB
O
AK303265
P
AB
THROTTLE
ACTUATOR
CONTROL
MOTOR RELAY
MFI RELAY
AK303195
Q
AB
FUEL PUMP
RELAY (1)
FUEL PUMP
RELAY (2)
AK303264
MALFUNCTION INDICATOR
LAMP (SERVICE ENGINE SOON)
AB
R
ON-VEHICLE SERVICE
TSB Revision
MULTIPORT FUEL INJECTION (MFI) <3.8L ENGINE>
13B-1178
THROTTLE BODY (THROTTLE VALVE AREA)
CLEANING
M1131001000503
WARNING
If the throttle valve is operation in service, a finger
might be injured as the result of being caught by the
throttle valve. Make sure that the ignition switch is
surely in "LOCK"(OFF) position before the service in
order that the throttle valve cannot be operation.
1. Remove the throttle body.
CAUTION
• Do not spray the cleaning solvent directly to the throttle
valve.
• Make sure the cleaning solvent does not enter the
motor and the sensor through the shaft.
2. Spray cleaning solvent on a clean cloth.
3. Wipe off the dirt around the throttle valve with the cloth
sprayed with cleaning solvent.
4. Attach the throttle body.
AK303196
S
AB
ACCELERATOR
PERAL
ACCELERATOR
PEDAL POSITION
SENSOR
AK303197
T
AB
DATA LINK
CONNECTOR
ACCELERATOR
PEDAL
AK303198
U
AB
FUEL LEVEL
SENSOR (SUB)
FUEL TANK
DIFFERENTIAL
PRESSURE
SENSOR
SERVICE
HOLE
AK303280
SERVICE
HOLE
V
FUEL PUMP MODULE
(INCORPORATING FUEL LEVEL
SENSOR (MAIN) AND FUEL
TANK TEMPERATURE SENSOR)
AB
AK303199
W
EVAPORATIVE EMISSION
VENTILATION SOLENOID
AB
EVAPORATIVE
EMISSION
CANISTER
ON-VEHICLE SERVICE
TSB Revision
MULTIPORT FUEL INJECTION (MFI) <3.8L ENGINE>
13B-1179
FUEL PRESSURE TEST
M1131001900584
Required Special Tools:
• MB991958: Scan tool (MUT-III Sub Assembly)
• MB991824: V.C.I.
• MB991827: USB Cable
• MB991910: Main Harness A
• MB991637: Fuel Pressure Gauge Set
• MD998709: Adaptor Hose
• MD998742: Hose Adaptor
1. Release residual pressure from the fuel line to prevent fuel
spray. (Refer to
WARNING
To prevent a fire, cover the hose connection with
shop towels to prevent splashing of fuel that could be
caused by some residual pressure in the fuel pipe
line.
2. Disconnect the fuel high-pressure hose at the fuel rail side.
3. Assemble the fuel pressure measurement tools as follows.
<When using the fuel pressure gauge>
1. Remove the union joint and bolt from special tool
MD998709 (adapter hose) and instead attach special tool
MD998742 (hose adapter) to the adapter hose.
2. Place a suitable O-ring or gasket on the assembled special
tools MD998709 and MD998742 and install the fuel pres-
sure gauge.
3. Install the assembled fuel pressure measurement tools
between the fuel rail and fuel high-pressure hose.
<When using special tool MB991637 (fuel pressure gauge
set)>
1. Remove the union joint and bolt from special tool
MD998709 (adapter hose) and instead attach special tool
MD998742 (hose adapter) to the adapter hose.
2. Install special tool MB991637 (fuel pressure gauge set) into
assembled special tools MD998709 and MD998742 via a
gasket.
3. Install the assembled fuel pressure measurement tools
between the fuel rail and fuel high-pressure hose.
AK203312AB
FUEL
HIGH-PRESSURE
HOSE
AKX01457AH
FUEL PRESSURE
GAUGE
O-RING OR GASKET
MD998709
MD998742
FUEL
RAIL
FUEL
HIGH-PRESSURE
HOSE
AKX01458
MB991637
O-RING OR GASKET
MD998709
MD998742
FUEL
RAIL
AI
FUEL
HIGH-PRESSURE
HOSE
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст