Mitsubishi Galant 9G. Manual — part 1558

COMBINATION METER ASSEMBLY

TSB Revision

CHASSIS ELECTRICAL

54A-104

CAUTION

To prevent damage to scan tool MB991958, always turn the
ignition switch to the "LOCK" (OFF) position before con-
necting or disconnecting scan tool MB991958.
1. Connect scan tool MB991958 to the data link connector.
2. A/T select lever: "P" position.
3. Turn the ignition switch to "ON" position.
4. Start the engine.
5. Run the engine.
6. Select MFI system data list and take a reading of the engine

speed.

Item 22: CKP SENSOR

7. Compare the engine speed shown in the scan tool with that

shown on the tachometer. The engine speeds shown on the
tachometer should correspond to the table below.
NOTE: The following standard value assumes that battery
voltage is 13.5 volts.

Standard value :

FUEL LEVEL SENSOR CHECK

M1543001300037

1. Remove the rear seat cusion assembly. (Refer to GROUP

52A, Rear Seat Assembly

P.52A-29

.)

2. Remove hole cover and remove the fuel pump module and

fuel level sensor (sub).

Tightening torque: 1.5

± 0.5 N⋅m (14 ± 0.5 in-Ib)

Engine speed (r/min)

Indication allowance of
tachometer r/min

600

600

± 100

2,000

2,000

± 100

3,000

3,000

± 150

4,000

4,000

± 150

5,000

5,000

± 150

6,000

6,000

± 150

AC305412

AB

MB991910

DATA LINK

CONNECTOR

MB991824

MB991827

AC307098AB

FUEL PUMP MODULE

WIRING COVER

1.5 ± 0.5 N·m
14 ± 4 in-lb

FUEL LEVEL SENSOR (SUB)

COMBINATION METER ASSEMBLY

TSB Revision

CHASSIS ELECTRICAL

54A-105

FUEL LEVEL SENSOR RESISTANCE

1. Check the resistances between fuel level sensor main

terminals 1 and 2 as well as sub terminals 1 and 2 of the fuel
pump module, respectively.

Standard value:

2. Check that resistance value changes smoothly when the

float moves slowly between points.

3. If all checks are correct, go to fuel unit height check. If any

check is not correct, replace the fuel pump module or fuel
level sensor (sub).

FUEL LEVEL SENSOR FLOAT HEIGHT

1. Move the float and measure height A at point "F" (highest)

and B at point "E" (lowest).

Standard value:

2. If any check is not correct, replace the fuel pump module or

fuel level sensor (sub).

Items

Fuel level
sensor
(main)

fuel level
sensor
(sub)

Resistance

Ω Point "F"

(highest)

6.5

± 1

6.5

± 1

Point "E"
(lowest)

44.6

± 1

75.4

± 1

AC307470

FUEL LEVEL SENSOR
(MAIN)

FUEL LEVEL SENSOR
(SUB)

F

E

E

F

AB

Items

Fuel level
sensor
(main)

Fuel level
sensor (sub)

Height
mm (in)

A at point
"F"

35.5

± 3.0

(1.4

± 0.1)

25.0

± 3.0

(1.0

± 0.1)

B at point
"E"

133.7

± 3.0

(5.3

± 0.1)

173.1

± 3.0

(68.1

± 0.1)

AC207587

AC307022

FUEL LEVEL SENSOR (MAIN)

POINT "F"

POINT "E"

AB

A

B

AC307023

AB

A

B

FUEL LEVEL SENSOR (SUB)

POINT "F"

POINT "E"

COMBINATION METER ASSEMBLY

TSB Revision

CHASSIS ELECTRICAL

54A-106

COMBINATION METER ASSEMBLY

REMOVAL AND INSTALLATION

M1543021300073

DISASSEMBLY AND ASSEMBLY

M1543003100352

AC306952AB

COMBINATION METER

NOTE:
THE COMBINATION METER CONNECTOR IS FIXED IN THE INSTRUMENT PANEL.

AC205381

1

2

AC

DISASSEMBLY STEPS

1. WINDOW PLATE
2. METER ASSEMBLY

HEADLIGHT, FRONT SIDE MARKER LIGHT AND POSITION LIGHT ASSEMBLY

TSB Revision

CHASSIS ELECTRICAL

54A-107

HEADLIGHT, FRONT SIDE MARKER LIGHT AND POSITION

LIGHT ASSEMBLY

HEADLIGHT DIAGNOSIS

M1542010500768

The headlights are controlled by the Simplified Wir-
ing System (SWS). For troubleshooting, refer to
GROUP 54B, SWS Diagnosis

− Symptom Chart

P.54B-59

.

ON-VEHICLE SERVICE

HEADLIGHT AIMING

M1542000900549

PRE-AIMING INSTRUCTIONS

1. Inspect for badly rusted or faulty headlight assemblies.
2. These conditions must be corrected before a satisfactory

adjustment can be made.

3. Inspect tire inflation, and adjust if it is necessary.
4. If the fuel tank is not full, place a weight in the trunk of the

vehicle to simulate weight of a full tank [3 kg (6.5 pounds)
per gallon].

5. There should be no other load in the vehicle other than

driver or substituted weight of approximately 70 kg (150
pounds) placed in driver's position.

6. Thoroughly clean headlight lenses.
7. Place the vehicle on a level floor, perpendicular to a flat

screen 7.62 m (25.0 feet) away from the bulb center-marks
on the headlight lens.

8. Rock vehicle sideways to allow vehicle to assume its normal

position.

9. Bounce the front suspension through three (3) oscillations

by applying the body weight to hood or bumper.