Mitsubishi Galant 9G. Manual — part 1523
POWER STEERING GEAR BOX AND LINKAGE
TSB Revision
POWER STEERING
37-42
Required Special Tools:
• MB990927: Installer Adapter
• MB990938: Bar (Snap-in type)
• MB990939: Brass Bar
• MB990996: Lower Arm Bushing Arbor
• MB991006: Preload Socket
• MB991120: Needle Bearing Puller
• MB991152: Dust Cover Installer
• MB991197: Bar (Long type)
• MB991199: Oil Seal Installer
• MB991202: Oil Seal and Bearing Installer
• MB991203: Oil Seal and Bearing Installer
• MB991204: Torque Wrench Socket
• MB991213: Rack Installer
• MB991317: Seal Ring Installer
• MB991561: Boot Band Crimping Tool
• MD998812: Installer Cap
• MD998813: Installer 100
• MD998822: Installer Adapter
• MD998368: Bearing Installer
• MD999569: Camshaft Oil Seal Installer
32.
STEERING GEAR PINION SHAFT
UPPER BEARING (NEEDLE
ROLLER BEARING)
33.
OIL SEAL
34.
STEERING GEAR CUSHION
35.
STEERING GEAR BUSHING
36.
RACK HOUSING
DISASSEMBLY STEPS (Continued)
POWER STEERING GEAR BOX AND LINKAGE
TSB Revision
POWER STEERING
37-43
LUBRICATION AND SEALING POINTS
AC307346 AC
GREASE: SILICONE GREASE
SEALANT:
3M
TM
AAD PART NO. 8661,
8663, 8672, 8678, 8679 OR
EQUIVALENT
FLUID:
GENUINE MITSUBISHI POWER
STEERING FLUID
FLUID:
GENUINE MITSUBISHI
POWER STEERING FLUID
FLUID:
GENUINE MITSUBISHI POWER
STEERING FLUID
FLUID:
GENUINE MITSUBISHI
POWER STEERING FLUID
FLUID:
GENUINE MITSUBISHI
POWER STEERING FLUID
POWER STEERING GEAR BOX AND LINKAGE
TSB Revision
POWER STEERING
37-44
DISASSEMBLY SERVICE POINTS
.
<<A>> STEERING TIE ROD/STEERING GEAR
WASHER (TAB WASHER) REMOVAL
Unstake the tab washer which secures the tie rod and rack with
a chisel.
.
<<B>> STEERING GEAR RACK SUPPORT
COVER REMOVAL
Using special tool MB991204, remove the rack support cover
from the gear box.
.
<<C>> OIL SEAL/PINION AND VALVE ASSEMBLY
REMOVAL
Using a plastic hammer, gently tap the pinion to remove it.
.
AC001001AB
TAB WASHER
ACX01142AB
MB991204
ACX01143 AB
POWER STEERING GEAR BOX AND LINKAGE
TSB Revision
POWER STEERING
37-45
<<D>> SEAL RING REMOVAL
CAUTION
When cutting the seal ring, be careful not to damage the
pinion and valve assembly or the rack.
Cut the seal ring and remove it from the pinion and valve
assembly and the rack.
.
<<E>> SPECIAL BEARING/OIL SEAL REMOVAL
Using a socket, remove the oil seal and the special bearing
from the valve housing simultaneously.
.
<<F>> STEERING GEAR PISTON CLIP (CIRCLIP)
REMOVAL
CAUTION
If the rack stopper is first turned counterclockwise, the cir-
clip will get caught in the slot in the housing and the rack
stopper will not turn.
1. Turn the rack stopper clockwise until the end of the circlip
comes out of the slot in the rack housing.
2. Turn the rack stopper counterclockwise to remove the
circlip.
.
ACX01144 AB
ACX01145AC
SOCKET
ACX01146 AB
CIRCLIP
RACK
STOPPER
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст