Mitsubishi Galant 9G. Manual — part 1560
HEADLIGHT, FRONT SIDE MARKER LIGHT AND POSITION LIGHT ASSEMBLY
TSB Revision
CHASSIS ELECTRICAL
54A-112
2. Remove the socket with the bulb by turning it
counterclockwise as shown.
CAUTION
Do not touch the surface of the bulb with hands or dirty
gloves as the bulb may fail after a short time. If the surface
does become dirty, clean it with alcohol or thinner, and let
it dry thoroughly before installing.
3. Pull out the bulb from the socket, and then replace the bulb.
4. Install the socket to the headlight by push and twisting it
clockwise.
Front Side-marker Light Bulb
1. Disconnect the front side-marker light connector.
2. Remove the socket with the bulb by turning it
counterclockwise as shown.
CAUTION
Do not touch the surface of the bulb with hands or dirty
gloves as the bulb may fail after a short time. If the surface
does become dirty, clean it with alcohol or thinner, and let
it dry thoroughly before installing.
3. Pull out the bulb from the socket, and then replace the bulb.
4. Install the socket to the headlight by push and twisting it
clockwise.
AC307139
FRONT TURN-SIGNAL
AND PARKING LIGHT
AB
AC307140
AB
FRONT SIDE-MARKER LIGHT
HEADLIGHT, FRONT SIDE MARKER LIGHT AND POSITION LIGHT ASSEMBLY
TSB Revision
CHASSIS ELECTRICAL
54A-113
HEADLIGHT AND FRONT COMBINATION LIGHT
REMOVAL AND INSTALLATION
M1542002700358
Post-installation operation
• Headlight aiming adjustment (Refer to
AC307154
1
4.9 ± 0.7 N·m
44 ± 6 in-lb
4.9 ± 0.7 N·m
44 ± 6 in-lb
1.5 ± 0.2 N·m
14 ± 1 in-lb
AB
HEADLIGHT REMOVAL STEPS
•
RADIATOR GRILL (REFER TO
GROUP 51, RADIATOR GRILL
.)
•
SPLASH SHIELD MOUNTING
CLIPS, FRONT BUMPER UNDER
COVER, RUBBER NUT, LICENSE
PLATE GARNISH (REFER TO
GROUP 51, FRONT BUMPER
<<A>>
1.
HEADLIGHT ASSEMBLY
HEADLIGHT REMOVAL STEPS
FOG LIGHT
TSB Revision
CHASSIS ELECTRICAL
54A-114
REMOVAL SERVICE POINT
.
<<A>> HEADLAIGHT ASSEMBLY REMOVAL
Remove the front bumper mounting screw and clip.
FOG LIGHT
FOG LIGHT DIAGNOSIS
M1542000701366
The fog lights are controlled by the Simplified Wiring
System (SWS). For troubleshooting, refer to GROUP
54B, SWS Diagnosis
ON-VEHICLE SERVICE
FOG LIGHT AIMING
M1542001100472
PRE-AIMING INSTRUCTIONS
1. Inspect for badly rusted or faulty fog light assemblies.
2. These conditions must be corrected before a satisfactory
adjustment can be made.
3. Inspect tire inflation, and adjust if necessary.
4. If the fuel tank is not full, place a weight in the trunk of the
vehicle to simulate weight of a full tank [3 kg (6.5 pounds)
per gallon].
5. There should be no other load in the vehicle other than
driver or substituted weight of approximately 70 kg (150
pounds) placed in driver's position.
6. Thoroughly clean the fog light lenses.
7. Place the vehicle on a level floor, perpendicular to a flat
screen 7.62 meters (25.0 feet) away from the bulb
center-marks on the foglight lens.
8. Rock the vehicle sideways to allow the vehicle to assume its
normal position.
9. Bounce the front suspension through three (3) oscillations
by applying the body weight to the hood or bumper.
AC307557
FOG LIGHT
TSB Revision
CHASSIS ELECTRICAL
54A-115
10.Measure the center of the fog lights as shown in the
illustration.
11.Four lines of adhesive tape (or equivalent markings) are
required on screen or wall:
(1) Position a vertical tape or mark so that it is aligned with
the vehicle center line.
(2) Measure the distance from the center of the fog light lens
to the floor. Transfer the measurement to the screen.
Horizontal tape or mark on the screen is for reference of
vertical adjustment.
(3) Measure the distance from the center line of the vehicle
to the center of each fog light. Transfer the measurement
to the screen. Vertical tape or mark on the screen is for
reference to the center line of each fog light.
FOG LIGHT ADJUSTMENT
1. Check if the beam shining onto the screen is at the standard
value.
2. If it is not within the standard value range, adjust by turning
the adjusting screw.
Standard value:
(Vertical direction): Top of the hot zone should be
101 mm (4.0 inches) (0.76 degrees angle) down-
ward from the height of the fog light center.
Limit:
(Vertical direction): Top of the hot zone should be
152mm (6.0 inches) (1.14 degrees angle) in maxi-
mum downward from the height of the fog light
center.
NOTE: The horizontal direction is non-adjustable. If deviation of
the light beam axis exceeds the standard value, check that the
mounting location or some other points are not faulty.
AC306966 AB
IN THE CENTER
OF FOG LIGHT
AC307983AB
SCREEN
(1)
(2)
(3)
(3)
FOG LIGHT CENTER
VEHICLE CENTER
LINE
7.62 m (25.0 ft)
AC100547
HEIGHT OF FOG
LIGHT CENTER
VERTICAL CENTER LINE
AHEAD OF FOG LIGHT
UPPER MOST LEVEL
OF HOT ZONE
HOT ZONE
mm (in)
AB
152 (6.0)
101 (4.0)
598 (23.5)
598 (23.5)
AC307156
AB
ADJUSTING SCREW
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст