Mitsubishi Galant 9G. Manual — part 451
AUTO-CRUISE CONTROL
TSB Revision
ENGINE AND EMISSION CONTROL
17-22
STEP 6. Check intermediate connector C-29, auto-cruise
control switch connector C-302 and clock spring
connectors C-303 and C-306 for loose, corroded or
damaged terminals, or terminals pushed back in the
connector.
Q: Are the connectors and terminals in good condition?
YES : Go to Step 7.
NO : Repair or replace the faulty connector. (Refer to
GROUP 00E, Harness Connector Inspection
). Install the air bag module (driver’s side).
(Refer to GROUP 52B, Air Bag Modules and Clock
Spring
AC305232
C-29
CONNECTOR: C-29
AC
C-29 MALE SIDE CONNECTOR
AC305236
C-306 HARNESS
CONNECTOR:
COMPONENT SIDE
C-303 HARNESS
CONNECTOR:
COMPONENT SIDE
C-302 HARNESS
CONNECTOR:
COMPONENT SIDE
AB
C-302 (Y)
C-303 (GR)
C-306
CONNECTORS: C-302, C-303, C-306
CLOCK
SPRING
AUTO-CRUISE CONTROL
TSB Revision
ENGINE AND EMISSION CONTROL
17-23
STEP 7. Check the harness wire between PCM connector
B-19 terminal 12 and auto-cruise control switch connector
C-302 terminal 2 for damage.
Q: Are the harness wires in good condition?
YES : Go to Step 8.
NO : Repair the damaged harness wire and install the air
bag module (driver’s side). (Refer to GROUP 52B, Air
Bag Modules and Clock Spring
). Then go
to Step 18.
STEP 8. Check the clock spring.
Refer to GROUP 52B, Air Bag Modules and Clock Spring
.
Q: Is the clock spring in good condition?
YES : It can be assumed that this malfunction is intermittent.
(Refer to GROUP 00, How to Use
Troubleshooting/Inspection Service Points
− How to
Cope with Intermittent Malfunction
). Install
the air bag module (driver’s side). (Refer to GROUP
52B, Air Bag Modules and Clock Spring
).
Then go to Step 18.
NO : Replace the clock spring and install the air bag
module (driver’s side). (Refer to GROUP 52B, Air Bag
Modules and Clock Spring
). Then go to
Step 18.
AC305710
B-19 HARNESS
CONNECTOR:
COMPONENT SIDE
AC
B-19 (B)
CONNECTOR: B-19
AIR CLEANER
PCM
AC305235AB
C-302 (Y)
CONNECTOR: C-302
C-302 HARNESS
CONNECTOR:
COMPONENT SIDE
CLOCK
SPRING
AUTO-CRUISE CONTROL
TSB Revision
ENGINE AND EMISSION CONTROL
17-24
STEP 9. Measure the ground voltage at auto-cruise control
switch connector C-302 by backprobing.
(1) Do not disconnect auto-cruise control switch connector
C-302.
(2) Turn the ignition switch to the "ON" position.
(3) Turn the "CRUISE" (MAIN) switch to the "ON" position.
(4) Measure the ground voltage between auto-cruise control
switch connector C-302 terminal 3 and ground by
backprobing.
(5) Turn the "CRUISE" (MAIN) switch to the "OFF" position.
(6) Turn the ignition switch to the "LOCK" (OFF) position.
Q: Is the measured voltage 0.5 volt or less?
YES : Go to Step 15.
NO : Go to Step 10.
AC305235AB
C-302 (Y)
CONNECTOR: C-302
C-302 HARNESS
CONNECTOR:
COMPONENT SIDE
CLOCK
SPRING
1 2
AC209264
3
AB
C-302 HARNESS
CONNECTOR:
HARNESS SIDE
AUTO-CRUISE CONTROL
TSB Revision
ENGINE AND EMISSION CONTROL
17-25
STEP 10. Measure the ground voltage at PCM connector
B-20.
(1) Disconnect all the connectors from the PCM.
(2) Connect special tool MB991923 between the PCM and the
body-side harness connector.
(3) Turn the ignition switch to the "ON" position.
(4) Turn the "CRUISE" (MAIN) switch to the "ON" position.
AC305710
B-20 HARNESS
CONNECTOR:
COMPONENT SIDE
AD
B-20
CONNECTOR: B-20
AIR CLEANER
PCM
AC209793AL
SPECIAL TOOL 23-PIN CONNECTOR
WITHOUT RED TAPE
(PCM CONNECTOR B-20)
B-20
25
21
24 23 22
29 28 27 26
34 33 32 31 30
38 37 36 35
43 42 41 40 39
PCM
MB991923
BODY SIDE
HARNESS
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст