Mitsubishi Galant 9G. Manual — part 452
AUTO-CRUISE CONTROL
TSB Revision
ENGINE AND EMISSION CONTROL
17-26
(5) Measure the ground voltage between special tool 23-pin
connector (without red tape) terminal 28 (PCM connector
B-20 terminal 28) and ground.
(6) Turn the "CRUISE" (MAIN) switch to the "OFF" position.
(7) Turn the ignition switch to the "LOCK" (OFF) position.
(8) Disconnect special tool MB991923 between the PCM and
the body-side harness connector.
(9) Reconnect all the connectors to the PCM.
Q: Is the measured voltage 0.5 volt or less?
YES : Go to Step 12.
NO : Go to Step 11.
STEP 11. Check PCM connector B-20 for loose, corroded
or damaged terminals, or terminals pushed back in the
connector.
Q: Are the connector and terminals in good condition?
YES : Install the air bag module (driver’s side). (Refer to
GROUP 52B, Air Bag Modules and Clock Spring
NO : Repair or replace the faulty connector. (Refer to
GROUP 00E, Harness Connector Inspection
). Install the air bag module (driver’s side).
(Refer to GROUP 52B, Air Bag Modules and Clock
Spring
AC209615 AB
SPECIAL TOOL 23-PIN
CONNECTOR
(WITHOUT RED TAPE):
COMPONENT SIDE
AC305710
B-20 HARNESS
CONNECTOR:
COMPONENT SIDE
AD
B-20
CONNECTOR: B-20
AIR CLEANER
PCM
AUTO-CRUISE CONTROL
TSB Revision
ENGINE AND EMISSION CONTROL
17-27
STEP 12. Check PCM connector B-20, intermediate
connector C-29, auto-cruise control switch connector
C-302 and clock spring connectors C-303 and C-306 for
loose, corroded or damaged terminals, or terminals
pushed back in the connector.
AC305710
B-20 HARNESS
CONNECTOR:
COMPONENT SIDE
AD
B-20
CONNECTOR: B-20
AIR CLEANER
PCM
AC305232
C-29
CONNECTOR: C-29
AC
C-29 MALE SIDE CONNECTOR
AUTO-CRUISE CONTROL
TSB Revision
ENGINE AND EMISSION CONTROL
17-28
Q: Are the connectors and terminals in good condition?
YES : Go to Step 13.
NO : Repair or replace the faulty connector. (Refer to
GROUP 00E, Harness Connector Inspection
). Install the air bag module (driver’s side).
(Refer to GROUP 52B, Air Bag Modules and Clock
Spring
AC305236
C-306 HARNESS
CONNECTOR:
COMPONENT SIDE
C-303 HARNESS
CONNECTOR:
COMPONENT SIDE
C-302 HARNESS
CONNECTOR:
COMPONENT SIDE
AB
C-302 (Y)
C-303 (GR)
C-306
CONNECTORS: C-302, C-303, C-306
CLOCK
SPRING
AUTO-CRUISE CONTROL
TSB Revision
ENGINE AND EMISSION CONTROL
17-29
STEP 13. Check the harness wire between PCM connector
B-20 terminal 28 and auto-cruise control switch connector
C-302 terminal 3 for damage.
Q: Are the harness wires in good condition?
YES : Go to Step 14.
NO : Repair the damaged harness wire and install the air
bag module (driver’s side). (Refer to GROUP 52B, Air
Bag Modules and Clock Spring
). Then go
to Step 18.
STEP 14. Check the clock spring.
Refer to GROUP 52B, Air Bag Modules and Clock Spring
.
Q: Is the clock spring in good condition?
YES : It can be assumed that this malfunction is intermittent.
(Refer to GROUP 00, How to Use
Troubleshooting/Inspection Service Points
− How to
Cope with Intermittent Malfunction
). Install
the air bag module (driver’s side). (Refer to GROUP
52B, Air Bag Modules and Clock Spring
).
Then go to Step 18.
NO : Replace the clock spring and install the air bag
module (driver’s side). (Refer to GROUP 52B, Air Bag
Modules and Clock Spring
). Then go to
Step 18.
AC305710
B-20 HARNESS
CONNECTOR:
COMPONENT SIDE
AD
B-20
CONNECTOR: B-20
AIR CLEANER
PCM
AC305235AB
C-302 (Y)
CONNECTOR: C-302
C-302 HARNESS
CONNECTOR:
COMPONENT SIDE
CLOCK
SPRING
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст