Mitsubishi Galant 9G. Manual — part 662
MULTIPORT FUEL INJECTION (MFI) DIAGNOSIS
TSB Revision
MULTIPORT FUEL INJECTION (MFI) <2.4L ENGINE>
13A-90
STEP 2. Measure the sensor supply voltage at manifold
absolute pressure sensor connector B-02 by backprobing.
(1) Do not disconnect the connector B-02.
(2) Turn the ignition switch to the "ON" position.
(3) Measure the voltage between terminal No. 3 and ground by
backprobing.
• Voltage should be between 4.9 and 5.1 volts.
(4) Turn the ignition switch to the "LOCK" (OFF) position.
Q: Is the measured voltage between 4.9 and 5.1 volts?
YES : Go to Step 8.
NO : Go to Step 3.
STEP 3. Check harness connector B-21 at PCM for
damage.
Q: Is the harness connector in good condition?
YES : Go to Step 4.
NO : Repair or replace it. Refer to GROUP 00E, Harness
. Then go to Step 12.
AK303809
1
2
3
AB
CONNECTOR: B-02
B-02 (B)
HARNESS CONNECTOR:
COMPONENT SIDE
3
2
1
AK203036
B-02 HARNESS
CONNECTOR:
HARNESS SIDE
AG
AK303018
55
56
54 53 52 51
57
62 61 60 59 58
63
69 68 67 66 65 64
70
75 74 73 72 71
76
82 81 80 79 78 77
83
CONNECTOR: B-21
PCM
AB
HARNESS CONNECTOR:
COMPONENT SIDE
AIR CLEANER
B-21 (B)
MULTIPORT FUEL INJECTION (MFI) DIAGNOSIS
TSB Revision
MULTIPORT FUEL INJECTION (MFI) <2.4L ENGINE>
13A-91
STEP 4. Measure the sensor supply voltage at PCM
connector B-21 by using power plant ECU check harness
special tool MB991923.
(1) Disconnect the all PCM connectors and connect power
plant ECU check harness special tool MB991923 between
the separated connectors.
(2) Turn the ignition switch to the "ON" position.
AK303018
55
56
54 53 52 51
57
62 61 60 59 58
63
69 68 67 66 65 64
70
75 74 73 72 71
76
82 81 80 79 78 77
83
CONNECTOR: B-21
PCM
AB
HARNESS CONNECTOR:
COMPONENT SIDE
AIR CLEANER
B-21 (B)
AK202989
55
56
54 53 52 51
57
62 61 60 59 58
63
69 68 67 66 65 64
70
75 74 73 72 71
76
82 81 80 79 78 77
83
AB
POWER PLANT ECU
CHECK HARNESS CONNECTOR
MB991923
PCM
MULTIPORT FUEL INJECTION (MFI) DIAGNOSIS
TSB Revision
MULTIPORT FUEL INJECTION (MFI) <2.4L ENGINE>
13A-92
(3) Measure the voltage between terminal No. 68 and ground.
• Voltage should be between 4.9 and 5.1 volts.
(4) Turn the ignition switch to the "LOCK" (OFF) position.
Q: Is the measured voltage between 4.9 and 5.1 volts?
YES : Go to Step 7.
NO : Go to Step 5.
STEP 5. Check harness connector B-02 at the manifold
absolute pressure sensor for damage.
Q: Is the connector in good condition?
YES : Go to Step 6.
NO : Repair or replace it. Refer to GROUP 00E, Harness
. Then go to Step 12.
55
56
54 53 52 51
57
62 61 60 59 58
63
69 68 67 66 65 64
70
75 74 73 72 71
76
82 81 80 79 78 77
83
AK203037AB
POWER PLANT ECU
CHECK HARNESS
CONNECTOR
AK303809
1
2
3
AB
CONNECTOR: B-02
B-02 (B)
HARNESS CONNECTOR:
COMPONENT SIDE
MULTIPORT FUEL INJECTION (MFI) DIAGNOSIS
TSB Revision
MULTIPORT FUEL INJECTION (MFI) <2.4L ENGINE>
13A-93
STEP 6. Check for short circuit to ground between
manifold absolute pressure sensor connector B-02
(terminal No. 3) and PCM connector B-21 (terminal No. 68).
Q: Is the harness wire in good condition?
YES : Go to Step 11.
NO : Repair it. Then go to Step 12.
STEP 7. Check harness connector B-02 at the manifold
absolute pressure sensor for damage.
Q: Is the connector in good condition?
YES : Repair harness wire between manifold absolute
pressure sensor connector B-02 (terminal No. 3) and
PCM connector B-21 (terminal No. 68) because of
open circuit. Then go to Step 12.
NO : Repair or replace it. Refer to GROUP 00E, Harness
. Then go to Step 12.
AK303809
1
2
3
AB
CONNECTOR: B-02
B-02 (B)
HARNESS CONNECTOR:
COMPONENT SIDE
AK303018
55
56
54 53 52 51
57
62 61 60 59 58
63
69 68 67 66 65 64
70
75 74 73 72 71
76
82 81 80 79 78 77
83
CONNECTOR: B-21
PCM
AB
HARNESS CONNECTOR:
COMPONENT SIDE
AIR CLEANER
B-21 (B)
AK303809
1
2
3
AB
CONNECTOR: B-02
B-02 (B)
HARNESS CONNECTOR:
COMPONENT SIDE
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст