Mitsubishi Galant 9G. Manual — part 410
DISC BRAKE ASSEMBLY
TSB Revision
BASIC BRAKE SYSTEM
35A-32
(4) Use a spring scale to measure the hub torque with pads
installed in the same direction as earlier.
(5) Calculate the drag force of the disc brake [difference
between hub torque with pads installed and hub torque
with pads removed].
Standard value:
<Front
−2.4L engine> 54 N (12 pounds) or less
<Front
−3.8L engine> 64 N (14 pounds) or less
<Rear> 54 N (12 pounds) or less
6. If the brake drag force exceeds the standard value,
disassemble and clean the piston. Check for corrosion or
worn piston seal, and check the sliding condition of the lock
pin and guide pin.
INSPECTION
M1351008100046
.
BRAKE DISC CHECK
• Disc run-out (Refer to
).
AC000908
SPRING SCALE
AF
<FRONT>
AC305369
SPRING SCALE
AB
<REAR>
DISC BRAKE ASSEMBLY
TSB Revision
BASIC BRAKE SYSTEM
35A-33
DISASSEMBLY AND ASSEMBLY <FRONT>
M1351008200065
AC307374
CLIP SET
CALIPER SEAL KIT
CALIPER KIT
SHIM SET
PAD SET
9
9
11
4
N
12
4
1
N
1
12
N
38 ± 4 N·m
28 ± 3 ft-lb
3
3
9
9
13
2
2
AB
10
8
5
6
7
12
9
4
13
4
11
9
13
N
6
7
N
8
5
38 ± 4 N·m
28 ± 3 ft-lb
15
14
7.9 ± 1.9 N·m
70 ± 16 in-lb
10
1
3
2
2
3
7
15
14
DISASSEMBLY STEPS
1. PAD (AND WEAR INDICATOR)
ASSEMBLY
2. CLIP
3. SHIM
4. FRONT BRAKE BOLT
5. CALIPER BODY
6. LOCK PIN
7. BUSH
8. GUIDE PIN
9. BOOT
10. CALIPER SUPPORT
<<A>>
11. CALIPER PISTON
<<A>>
12. PISTON BOOT
<<B>>
13. PISTON SEAL
14. CALIPER BLEEDER CAP
15. CALIPER BLEEDER
DISASSEMBLY STEPS (Continued)
DISC BRAKE ASSEMBLY
TSB Revision
BASIC BRAKE SYSTEM
35A-34
LUBRICATION POINTS
DISASSEMBLY SERVICE POINTS
CAUTION
When disassembling the front disc brakes, disassemble
both sides (left and right wheels) as a set.
.
AC307433
AB
GREASE: REPAIR KIT GREASE
GREASE: REPAIR KIT GREASE
BRAKE FLUID: DOT3 OR DOT4
THE PISTON SEAL INSIDE THE
CALIPER SEAL KIT IS COATED
WITH SPECIAL GREASE DO NOT
WIPE THIS GREASE OFF.
GREASE: REPAIR KIT GREASE
PISTON
SEAL
CAUTION
DISC BRAKE ASSEMBLY
TSB Revision
BASIC BRAKE SYSTEM
35A-35
<<A>> CALIPER PISTON/PISTON BOOT
REMOVAL
CAUTION
Blow air little by little to remove the piston. The piston will
pop out if a force of air is applied suddenly.
Place a piece of wood, etc. against the caliper body as shown.
Blow compressed air through the brake hose connection hole
to remove the piston boot and piston.
.
<<B>> PISTON SEAL REMOVAL
CAUTION
Do not use a flat-tipped screwdriver or similar tool to
remove the piston seal. These may damage the inner side
of the cylinder.
1. Remove the piston seal with your finger tip.
2. Clean the piston surface and inner cylinder with alcohol
brake fluid DOT 3 or DOT 4.
AC204331
ACX00689
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст