Mitsubishi Galant 9G. Manual — part 1386
OIL PAN AND OIL SCREEN
TSB Revision
ENGINE MECHANICAL <3.8L ENGINE>
11C-38
INSTALLATION SERVICE POINTS
.
>>A<< ENGINE UPPER OIL PAN INSTALLATION
1. Remove sealant from the oil pan and cylinder block mating
surfaces.
2. Degrease the sealant-coated surface and the engine mating
surface.
3. Apply a bead of the sealant to the cylinder block mating
surface of the engine oil pan as shown.
Specified sealant: 3M
AAD Part No.8672, 8704, 3M
AAD Part No.8679/8678 or equivalent
NOTE: The sealant should be applied in a continuous bead
approximately 4.0 mm (0.16 inch) in diameter.
4. Assemble the oil pan to the cylinder block within 15 minutes
after applying the sealant.
CAUTION
The bolt holes for bolts 13 and 14 in the illustration are cut
away on the transaxle side. Be careful not to insert these
bolts at an angle.
5. Tighten the bolts in order of the numbers shown in the
illustration.
.
AC308675
Ø 4.0 mm
(0.16 in)
GROOVE
PORTION
BOLT HOLE
PORTION
AB
AC206507
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
AB
CYLINDER BLOCK
REAR OIL SEAL CASE
OIL PAN
TRANSAXLE
SIDE
13, 14
OIL PAN AND OIL SCREEN
TSB Revision
ENGINE MECHANICAL <3.8L ENGINE>
11C-39
>>B<< ENGINE LOWER OIL PAN INSTALLATION
1. Remove sealant from the engine lower oil pan and engine
upper oil pan.
2. Apply a bead of the sealant to the mating surface of the
engine lower oil pan as shown.
Specified sealant: 3M
AAD Part No.8672, 8704, 3M
AAD Part No.8679/8678 or equivalent
NOTE: Install the engine lower oil pan within 15 minutes
after applying sealant.
3. Assemble the engine lower oil pan to the engine upper oil
pan.
CAUTION
Then wait at least one hour. Never start the engine or let
engine oil or coolant touch the sealant surface during that
time.
4. Tighten the bolts in order of the numbers shown in the
illustration.
INSPECTION
M1112002600134
• Check the oil pan for cracks.
• Check the oil pan sealant-coated surface for damage and
deformation.
• Check the oil screen for cracked, clogged or damaged wire
net and pipe.
AC205271
Ø 4.0 mm
(0.16 in)
GROOVE
PORTION
BOLT HOLE
PORTION
AB
AC206508
1
2
3
4
5
6
7
8
AB
CRANKSHAFT OIL SEAL
TSB Revision
ENGINE MECHANICAL <3.8L ENGINE>
11C-40
CRANKSHAFT OIL SEAL
REMOVAL AND INSTALLATION <FRONT OIL SEAL>
M1112003400478
Required Special Tool:
MD998717: Crankshaft Front Oil Seal Installer
Pre-removal and Post-installation Operation
Timing Belt Removal and Installation (Refer to
AC205520
6
ENGINE OIL
1
2
3
4
5
6
N
8.5 ± 0.5 N·m
76 ± 4 in-lb
AB
REMOVAL STEPS
1.
CRANKSHAFT POSITION
SENSOR
>>B<<
2.
CRANKSHAFT SPROCKET
>>B<<
3.
CRANKSHAFT SENSING BLADE
>>B<<
4.
CRANKSHAFT SPACER
5.
KEY
>>A<<
6.
CRANKSHAFT FRONT OIL SEAL
REMOVAL STEPS (Continued)
CRANKSHAFT OIL SEAL
TSB Revision
ENGINE MECHANICAL <3.8L ENGINE>
11C-41
INSTALLATION SERVICE POINTS
.
>>A<< CRANKSHAFT FRONT OIL SEAL INSTAL-
LATION
1. Apply a small amount of engine oil to the oil seal lip and then
insert.
2. Using special tool MD998717, tap the oil seal into the front
case.
.
>>B<< CRANKSHAFT SPACER / CRANKSHAFT
SENSING BLADE / CRANKSHAFT SPROCKET
INSTALLATION
To prevent the crankshaft pulley mounting bolt from loosening,
degrease or clean the crankshaft, the crankshaft spacer, the
crankshaft sensing blade and the crankshaft at the shown posi-
tions.
ACX00363AB
OIL SEAL
MD998717
CRANKSHAFT
MD998717
ACX01536AB
CRANKSHAFT
CRANKSHAFT
SPACER
CRANKSHAFT
SENSING BLADE
CRANKSHAFT
SPROCKET
SHADED PART : DEGREASE
CLEANING
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст