Mitsubishi Galant 9G. Manual — part 1385
CAMSHAFT AND VALVE STEM SEAL
TSB Revision
ENGINE MECHANICAL <3.8L ENGINE>
11C-34
>>D<< ROCKER ARM AND SHAFT ASSEMBLY
INSTALLATION
1. Install the rocker arm, shaft and lash adjuster assembly.
2. Tighten the mounting bolts to the specified torque.
Tightening torque: 31
± 3 N⋅m (23 ± 2 ft-lb)
3. Remove special tool MD998443.
4. Check that notches in the each rocker shaft are facing the
direction shown in the illustration.
.
AC205280
MD998443
AB
AC204149
AC
NOTCH
NOTCH
FRONT
NOTCH
NOTCH
<RIGHTBANK>
<LEFTBANK>
CAMSHAFT AND VALVE STEM SEAL
TSB Revision
ENGINE MECHANICAL <3.8L ENGINE>
11C-35
>>E<< CAMSHAFT OIL SEAL INSTALLATION
1. Apply engine oil to the camshaft oil seal lip.
2. Use special tools MD998713 and MB991559 to press-fit the
camshaft oil seal.
.
>>F<< CAMSHAFT SPROCKET INSTALLATION
1. Use special tools MD998715 and MB990767 in the same
way as during removal to install the camshaft sprocket.
2. Tighten the camshaft sprocket mounting bolt to the specified
torque.
Tightening torque: 88
± 10 N⋅m (65 ± 7 ft-lb)
ACX00371AB
MB991559
MD998713
<LEFT BANK>
ACX00372 AB
MD998713
<RIGHT BANK>
ACX00301AB
MB990767
MD998715
OIL PAN AND OIL SCREEN
TSB Revision
ENGINE MECHANICAL <3.8L ENGINE>
11C-36
OIL PAN AND OIL SCREEN
REMOVAL AND INSTALLATION
M1112002500193
Pre-removal and Post-installation Operation
• Under Cover Removal and Installation (Refer to GROUP
51, Under Cover
• Engine Oil Draining and Refilling (Refer to GROUP 12,
On-vehicle Service
AC308673
1
2
3
4
5
6
7
8
9
10
11
12
11 ± 0.5 N·m
93 ± 4 in-lb
49 ± 3 N·m
36 ± 2 ft-lb
35 ± 5 N·m
26 ± 4 ft-lb
30 ± 3 N·m
23 ± 2 ft-lb
30 ± 3 N·m
23 ± 2 ft-lb
14 ± 1 N·m
120 ± 13 in-lb
11 ± 1 N·m
97 ± 9 in-lb
39 ± 5 N·m
29 ± 3 ft-lb
19 ± 3 N·m
14 ± 2 ft-lb
8.5 ± 3.5 N·m
76 ± 31 in-lb
N
N
N
AB
6
5
ENGINE OIL
REMOVAL STEPS
1.
ENGINE OIL PAN DRAIN PLUG
2.
ENGINE OIL PAN DRAIN PLUG
GASKET
3.
STARTER CONNECTOR
4.
STARTER ASSEMBLY
5.
ENGINE OIL DIPSTICK
ASSEMBLY
6.
O-RING
7.
ENGINE LOWER OIL PAN
•
FRONT NO.1 EXHAUST PIPE
(REFER TO GROUP 15,
EXHAUST PIPE AND MAIN
MUFFLER
8.
COVER
<<B>>
9.
TORQUE CONVERTER
CONNECTING BOLT
<<C>>
>>A<<
10. ENGINE UPPER OIL PAN
11. OIL SCREEN
12. GASKET
REMOVAL STEPS (Continued)
OIL PAN AND OIL SCREEN
TSB Revision
ENGINE MECHANICAL <3.8L ENGINE>
11C-37
REMOVAL SERVICE POINT
.
<<A>> ENGINE LOWER OIL PAN REMOVAL
1. Remove the engine lower oil pan mounting bolts.
CAUTION
Do not use oil pan remover special tool (MD998727). The
engine upper oil pan is made of aluminum and this tool will
damage it.
2. Apply a piece of wood to the lower oil pan and strike it with a
hammer to remove the engine lower oil pan.
.
<<B>> TORQUE CONVERTER CONNECTING
BOLT REMOVAL
Remove the one torque converter connecting bolt as shown.
.
<<C>> ENGINE UPPER OIL PAN REMOVAL
1. Remove the engine upper oil pan mounting bolts.
CAUTION
Do not use oil pan remover special tool (MD998727). The
engine upper oil pan is made of aluminum and this tool will
damage it.
2. Screw in the bolt (M10) into bolt hole A in the location
shown. Then lift the upper oil pan and remove it.
AC206414
LOWER OIL PAN
AB
AC206538
49 ± 3 N·m
36 ± 2 ft-lb
AB
AC206525 AB
A
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст