Mitsubishi Galant 9G. Manual — part 111
SYMPTOM PROCEDURES
TSB Revision
SIMPLIFIED WIRING SYSTEM (SWS)
54B-440
STEP 3. Use scan tool MB991958 to select "ECU COMM
Check" on the SWS monitor display.
Check the ETACS-ECU.
CAUTION
To prevent damage to scan tool MB991958, always turn the
ignition switch to the "LOCK" (OFF) position before con-
necting or disconnecting scan tool MB991958. Connect
special tool MB991910 before connecting special tool
MB991812. Be sure to connect special tool MB991806 after
turning on special tool MB991824.
(1) Connect the special tool. Refer to "How to connect SWS
."
(2) Turn the ignition switch to the "LOCK" (OFF) position.
(3) Operate scan tool MB991958 according to the procedure
below to display "ECU COMM Check."
a. Select "Interactive Diagnosis."
b. Select "System select."
c. Select "SWS."
d. Select "SWS MONITOR."
e. Select "ECU COMM Check."
(4) Scan tool MB991958 should show "OK" on the "ECU
COMM Check" menu for the "ETACS ECU" menu.
Q: Is "OK" displayed for the "ETACS ECU" menu?
YES : Go to Step 4.
NO : Refer to Inspection Procedure A-3 "Communication
with the ETACS-ECU is not possible
."
AC305411AB
MB991910
DATA LINK
CONNECTOR
MB991827
MB991824
MB991806
MB991812
AC302210
COLUMN SWITCH
CONNECTOR
COLUMN SWITCH
CONNECTOR AT
HARNESS SIDE
MB991812
AB
SYMPTOM PROCEDURES
TSB Revision
SIMPLIFIED WIRING SYSTEM (SWS)
54B-441
STEP 4. Check the input signal by using "DATA LIST"
menu of the SWS monitor.
Check the input signals from the following switches:
• Ignition switch: OFF
• Driver’s or front passenger’s door: open
(1) Operate scan tool MB991958 according to the procedure
below to display "ETACS ECU."
a. Select "Interactive Diagnosis."
b. Select "System select."
c. Select "SWS."
d. Select "SWS MONITOR."
e. Select "Data List."
f. Select "ETACS ECU."
(2) Check that normal conditions are displayed for the item
described in the table below.
Q: Does the scan tool MB991958 display "IG SW (IG1)" as
normal condition?
YES : Go to Step 5.
NO : Refer to Inspection Procedure M-2 "ETACS-ECU
does not receive any signal from the ignition switch
(IG1)
ITEM NO.
ITEM NAME
NORMAL CONDITION
ITEM 30
IG SW (IG1)
OFF
AC305411AB
MB991910
DATA LINK
CONNECTOR
MB991827
MB991824
MB991806
MB991812
AC302210
COLUMN SWITCH
CONNECTOR
COLUMN SWITCH
CONNECTOR AT
HARNESS SIDE
MB991812
AB
SYMPTOM PROCEDURES
TSB Revision
SIMPLIFIED WIRING SYSTEM (SWS)
54B-442
STEP 5. Check the input signal (by using the pulse check
mode of the monitor).
Check the input signals from the following switches:
• Key reminder switch
• Door switches
• Trunk lid latch assembly
(1) Operate scan tool MB991958 according to the procedure
below to display "Pulse check."
a. Select "Interactive Diagnosis."
b. Select "System select."
c. Select "SWS."
d. Select "Pulse Checking."
(2) Check if scan tool MB991958 sounds or not.
Q: When the key reminder switch, any door switch, or the
trunk lid is operated, does scan tool MB991958 sound?
Buzzer of scan tool MB991958 sounds normally. :
Replace the ETACS-ECU. Verify that the dome light
dimming function works normally.
Scan tool MB991958 does not sound when the ignition
key is removed and reinserted : Refer to Inspection
Procedure N-1 "ETACS-ECU does not receive a
signal from the key reminder switch
."
Scan tool MB991958 does not sound whenever a door
switch is operated : Refer to Inspection Procedure N-3
"ETACS-ECU does not receive any signal from any of
the door switches
When the trunk lid is opened and closed, scan tool
MB991958 does not sound. : Refer to Inspection
Procedure N-7 "ETACS-ECU does not receive any
signal from trunk lid latch assembly
ITEM NAME
CONDITION
key reminder switch
Remove and reinsert the ignition
key
door switches
Open or close one of the doors
trunk lid latch assembly
Open or close the trunk lid
AC305412
AB
MB991910
DATA LINK
CONNECTOR
MB991824
MB991827
SYMPTOM PROCEDURES
TSB Revision
SIMPLIFIED WIRING SYSTEM (SWS)
54B-443
INSPECTION PROCEDURE K-4: Interior Light: The ignition key hole illumination light does not
illuminate or go out normally.
NOTE: This troubleshooting procedure requires the
use of scan tool MB991958 and SWS monitor kit
MB991813. For details on how to use the SWS mon-
itor, refer to "How to use SWS monitor
BATTERY
RELAY
BOX
KEY REMINDER
SWITCH
IGNITION
KEY HOLE
ILLUMINATION
LIGHT
· FRONT DOOR SWITCH
· IGNITION SWITCH (IG1)
· KEY REMINDER SWITCH
ETACS-
ECU
JOINT
CONNECTOR (1)
Ignition Key Hole Illumination Light Circuit
AC305231
C-01
C-29
CONNECTORS: C-01, C-29
BI
AC305413AL
CONNECTOR: C-218
C-218 (GR)
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст