Mitsubishi Galant 9G. Manual — part 1397
FUEL TANK
TSB Revision
FUEL SUPPLY
13C-16
>>C<< FUEL HIGH-PRESSURE HOSE/FUEL
HIGH-PRESSURE HOSE CONNECTION
INSTALLATION
CAUTION
Connect the fuel high-pressure hose, and then pull it gen-
tly in the direction of removal to check that the hose is
firmly connected.
Apply clean engine oil to the tips of the main pipe nozzle and
the fuel main pipe, and connect connector of the fuel high-pres-
sure hose to them.
.
>>D<< FUEL TANK BAND/FUEL TANK ASSEMBLY
INSTALLATION
1. Raise the fuel tank assembly carefully with a transaxle jack.
2. Ensure that the fuel tank assembly does not interfere with
surrounding parts. Then install the fuel tank band and
tighten the mounting nuts to the specified torque.
Tightening torque: 26
± 4 N⋅m (19 ± 3 ft-lb)
3. Again, ensure that the fuel tank assembly does not interfere
with surrounding components. If the fuel tank assembly
interferes surrounding components, remove the fuel tank
assembly and the tank band and reinstall them.
INSPECTION
M1135002000241
.
FUEL SHUT-OFF VALVE CHECK
Check that the flapper of the fuel shut-off valve opens and
closes as shown in the illustration.
.
AC209221
CONNECTOR
MAIN PIPE NOZZLE OR
FUEL MAIN PIPE
AB
AC005004AB
CLOSED
OPEN
FLAPPER
80˚
SPECIFICATIONS
TSB Revision
FUEL SUPPLY
13C-17
FUEL TANK DIFFERENTIAL PRESSURE SENSOR
CHECK
Requird Special Tool:
• MB991658: Test Harness Set
1. Disconnect the fuel tank differential pressure sensor
connector and connect special tool MB991658 between the
terminals of the disconnected connector.
2. Turn the ignition switch to “ON” position and measure the
voltage between terminal 1 and ground.
Standard value: 2.0
− 3.0 V
SPECIFICATIONS
FASTENER TIGHTENING SPECIFICATIONS
M1135003900322
SERVICE SPECIFICATION
M1135000300257
AC002081AB
MB991658
FUEL TANK DIFFERENTIAL
PRESSURE SENSOR
ITEM
SPECIFICATIONS
Fuel tank band nut
26
± 4 N⋅m (19 ± 3 ft-lb)
Hole cover screw
1.5
± 0.5 N⋅m (14 ± 4 in-lb)
ITEM
STANDARD VALUE
Fuel tank differential pressure sensor output voltage V
2.0
− 3.0
NOTES
52B-1
GROUP 52B
SUPPLEMENTAL
RESTRAINT
SYSTEM (SRS)
CONTENTS
GENERAL DESCRIPTION. . . . . . . . .
SERVICE PRECAUTIONS. . . . . . . . .
SRS AIR BAG DIAGNOSIS . . . . . . . .
INTRODUCTION TO DIAGNOSIS . . . . . . .
TROUBLESHOOTING STRATEGY . . . . . .
DIAGNOSTIC FUNCTION . . . . . . . . . . . . .
SRS WARNING LIGHT CHECK . . . . . . . . .
PASSENGER'S SEAT BELT WARNING
LIGHT CHECK . . . . . . . . . . . . . . . . . . . . . .
PASSENGER'S AIR BAG OFF INDICATOR
LIGHT CHECK . . . . . . . . . . . . . . . . . . . . . .
DIAGNOSTIC TROUBLE CODE CHART . .
DIAGNOSTIC TROUBLE CODE
PROCEDURES. . . . . . . . . . . . . . . . . . . . . .
TROUBLE SYMPTOM CHART. . . . . . . . . .
SYMPTOM PROCEDURES . . . . . . . . . . . .
DATA LIST REFERENCE TABLE . . . . . . . .
ACTUATOR TEST REFERENCE TABLE . .
FAIL-SAFE FUNCTION . . . . . . . . . . . . . . . .
ACCURACY TESTING OF OCCUPANT
CLASSIFICATION SENSOR . . . . . . . . . . . .
SPECIAL TOOLS . . . . . . . . . . . . . . . .
TEST EQUIPMENT . . . . . . . . . . . . . . .
SRS MAINTENANCE . . . . . . . . . . . . .
POST-COLLISION DIAGNOSIS. . . . .
INDIVIDUAL COMPONENT
SERVICE. . . . . . . . . . . . . . . . . . . . . . .
Continued on next page
Battery posts, terminals and related accessories contain lead and lead compounds. WASH HANDS
AFTER HANDLING.
WARNING
WARNING
•
Carefully read and observe the information in the SRS SERVICE PRECAUTIONS prior to any service.
•
For information concerning diagnosis or maintenance, always observe the procedures in the SRS Diagnosis or
the SRS Maintenance sections, respectively.
•
If any SRS components are removed or replaced in connection with any service procedures, be sure to follow the
procedures in the INDIVIDUAL COMPONENT SERVICE section for the comportments involved.
•
If you have any questions about the SRS, please contact the MMNA Tech Line.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст