Mitsubishi Galant 9G. Manual — part 581
TRANSAXLE ASSEMBLY
TSB Revision
AUTOMATIC TRANSAXLE
23A-402
>>D<< DRIVE SHAFT NUT INSTALLATION
1. Be sure to install the drive shaft washer in the specified
direction.
CAUTION
Before securely tightening the drive shaft nuts, make sure
there is no load on the wheel bearings. Otherwise the
wheel bearing will be damaged.
2. Using special tool MB990767, tighten the drive shaft nut to
the specified torque.
Tightening torque: 226
± 29 N⋅m (167 ± 21 ft-lb)
.
>>E<< TRANSAXLE CONTROL
CABLE/ADJUSTING NUT INSTALLATION
1. Place the selector lever and manual control lever in the “N”
position.
2. Place the cable stud into the manual control lever slot and
install the nut loosely. Gently push the transaxle control
cable into the manual control lever slot until the cable is taut.
Tighten the nut to the specified torque.
Tightening torque: 12
± 2 N⋅m (107 ± 17 in-lb)
AC210244AB
MB990767
WASHER
AC305881AD
12 ± 2 N·m
107 ± 17 in-lb
ADJUSTING NUT
MANUAL
CONTROL
LEVER
<F4A5A>
TRANSMISSION FLUID COOLER, HOSE AND PIPE
TSB Revision
AUTOMATIC TRANSAXLE
23A-403
TRANSMISSION FLUID COOLER, HOSE AND PIPE
REMOVAL AND INSTALLATION
M1231021900044
<F4A4B>
Pre-removal and Post-installation Operation
• Engine Coolant Draining and Supplying (Refer to GROUP
00
− Maintenance Service
• Transmission Fluid Draining and Supplying (Refer to
GROUP 00, Maintenance Service
− Automatic Transmis-
sion Fluid
• Air Cleaner Intake Duct Removal and Installation (Refer to
GROUP 15, Air Cleaner
AC306185AB
23 ± 3 N·m
17 ± 2 ft-lb
23 ± 3 N·m
17 ± 2 ft-lb
1
2
3
4
6
5
REMOVAL STEPS
<<A>>
1.
TRANSMISSION FLUID COOLER
RETURN HOSE
<<A>>
2.
TRANSMISSION FLUID COOLER
FEED HOSE
<<A>>
3.
WATER COOLER FEED HOSE
<<A>>
4.
WATER COOLER RETURN HOSE
•
ATF WARMER (TRANSMISSION
FLUID COOLER) AND ATF
WARMER (TRANSMISSION
FLUID COOLER) BRACKET
5.
ATF WARMER (TRANSMISSION
FLUID COOLER) BRACKET
<<A>>
6.
ATF WARMER (TRANSMISSION
FLUID COOLER)
REMOVAL STEPS (Continued)
TRANSMISSION FLUID COOLER, HOSE AND PIPE
TSB Revision
AUTOMATIC TRANSAXLE
23A-404
REMOVAL SERVICE POINTS
.
<<A>> TRANSMISSION FLUID COOLER RETURN
HOSE/TRANSMISSION FLUID COOLER FEED
HOSE/WATER COOLER FEED HOSE/WATER
COOLER RETURN HOSE/ATF WARMER (TRANS-
MISSION FLUID COOLER) REMOVAL
Drain the transmission fluid and engine coolant, which still
remained in the hoses and the ATF warmer (transmission fluid
cooler).
REMOVAL AND INSTALLATION
M1231021900033
<F4A5A>
Pre-removal and Post-installation Operation
• Transmission Fluid Draining and Supplying (Refer to
GROUP 00, Maintenance Service
− Automatic Transmis-
sion Fluid
• Front Under Cover <LH> Removal and Installation
AC306186
1
2
3
AB
TRANSMISSION FLUID COOLER
LINE ASSEMBLY REMOVAL
STEPS
<<A>>
1.
HOSE ASSEMBLY CONNECTION
<RADIATOR SIDE>
•
AIR CLEANER ASSEMBLY
(REFER TO GROUP 15
<<A>>
2.
HOSE ASSEMBLY CONNECTION
<TRANSAXLE SIDE>
3.
HOSE ASSEMBLY
TRANSMISSION FLUID COOLER
LINE ASSEMBLY REMOVAL
STEPS (Continued)
SPECIFICATIONS
TSB Revision
AUTOMATIC TRANSAXLE
23A-405
REMOVAL SERVICE POINTS
.
<<A>> HOSE ASSEMBLY <RADIATOR
SIDE>/HOSE ASSEMBLY <TRANSAXLE SIDE>
REMOVAL
Drain the transmission fluid, which still remained in the hose
assembly and the transmission fluid cooler.
SPECIFICATIONS
FASTENER TIGHTENING SPECIFICATIONS
M1231012400245
ITEM
SPECIFICATION
Transmission range switch
Transmission range switch body mounting bolt
11
± 1 N⋅m (96 ± 8 in-lb)
Transaxle control
Adjusting nut
12
± 2 N⋅m (107 ± 17 in-lb)
Shift knob attaching screw
2.0
± 0.3 N⋅m (18 ± 2 in-lb)
Selector lever assembly attaching bolt
12
± 2 N⋅m (102 ± 22 in-lb)
Shift lock cable unit fixing bolt
5.0
± 1.0 N⋅m (44 ± 9 in-lb)
Transaxle control cable attaching bolt
12
± 2 N⋅m (102 ± 22 in-lb)
Key interlock and shift lock mechanisms
Shift lock cable unit fixing bolt
5.0
± 1.0 N⋅m (44 ± 9 in-lb)
Transaxle assembly
Adjusting nut
12
± 2 N⋅m (107 ± 17 in-lb)
ATF warmer (transmission fluid cooler) bracket attaching bolt <F4A4B>
23
± 3 N⋅m (17 ± 2 ft-lb)
Bell housing cover attaching bolt (engine side) <F4A4B>
9.0
± 1.0 N⋅m (80 ± 9 in-lb)
Bell housing cover attaching bolt (transaxle side) <F4A4B>
26
± 5 N⋅m (19 ± 4 ft-lb)
Center member attaching bolt
83
± 12 N⋅m (61 ± 9 ft-lb)
Cover attaching bolt <F4A5A>
11
± 0.5 N⋅m (93 ± 4 in-lb)
Drive plate bolt
49
± 3 N⋅m (36 ± 2 ft-lb)
Drive shaft and inner shaft assembly bolt (RH) <F4A5A>
41
± 4 N⋅m (30 ± 3 ft-lb)
Drive shaft nut
226
± 29 N⋅m (167 ± 21 ft-lb)
Engine oil pan and transaxle coupling bolt <F4A5A>
35
± 6 N⋅m (26 ± 4 ft-lb)
Front roll stopper bracket retainer nut
58
± 7 N⋅m (43 ± 5 ft-lb)
Rear roll stopper bracket attaching bolt
90
± 10 N⋅m (67 ± 7 ft-lb)
Rear roll stopper bracket retainer nut
58
± 7 N⋅m (43 ± 5 ft-lb)
Self-locking nut (lower arm ball joint connection)
65
± 6 N⋅m (48 ± 4 ft-lb)
Self-locking nut (tie rod end connection)
29
± 4 N⋅m (21 ± 3 ft-lb)
Stabilizer link to strut connecting nut
48
± 7 N⋅m (36 ± 5 ft-lb)
Starter motor attaching bolt
30
± 3 N⋅m (23 ± 2 ft-lb)
Starter terminal nut
12
± 2 N⋅m (102 ± 22 in-lb)
Transaxle assembly upper part coupling bolt <F4A4B>
48
± 6 N⋅m (36 ± 4 ft-lb)
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст