Mitsubishi Galant 9G. Manual — part 852
MULTIPORT FUEL INJECTION (MFI) DIAGNOSIS
TSB Revision
MULTIPORT FUEL INJECTION (MFI) <2.4L ENGINE>
13A-850
STEP 6. Check harness connector B-22 at PCM for
damage.
Q: Is the harness connector in good condition?
YES : Go to Step 7.
NO : Repair or replace it. Refer to GROUP 00E, Harness
. Then go to Step 10.
AK303016
104
96
94
95
93 92 91
99 98 97
103 102 101 100
108 107 106 105
113 112 111 110 109
CONNECTOR: B-22
B-22 (B)
PCM
AB
HARNESS CONNECTOR:
COMPONENT SIDE
AIR CLEANER
MULTIPORT FUEL INJECTION (MFI) DIAGNOSIS
TSB Revision
MULTIPORT FUEL INJECTION (MFI) <2.4L ENGINE>
13A-851
STEP 7. Check for harness damage between engine oil
pressure switch connector B-34 (terminal No. 1) and PCM
connector B-22 (terminal No. 110).
Q: Is the harness wire in good condition?
YES : Go to Step 8.
NO : Repair it. Then go to Step 10.
AK303894
1
AK303894
1
AB
CONNECTOR: B-34
B-34 (B)
HARNESS CONNECTOR:
COMPONENT SIDE
RADIATOR
UPPER HOSE
AK303016
104
96
94
95
93 92 91
99 98 97
103 102 101 100
108 107 106 105
113 112 111 110 109
CONNECTOR: B-22
B-22 (B)
PCM
AB
HARNESS CONNECTOR:
COMPONENT SIDE
AIR CLEANER
MULTIPORT FUEL INJECTION (MFI) DIAGNOSIS
TSB Revision
MULTIPORT FUEL INJECTION (MFI) <2.4L ENGINE>
13A-852
STEP 8. Using scan tool MB991958, check actuator test
item 22: Engine Oil Control Valve.
CAUTION
To prevent damage to scan tool MB991958, always turn the
ignition switch to the "LOCK" (OFF) position before con-
necting or disconnecting scan tool MB991958.
(1) Connect scan tool MB991958 to the data link connector.
(2) Turn the ignition switch to the "ON" position.
(3) Set scan tool MB991958 to the actuator test mode for item
22, Engine oil control valve.
• An operation sound should be heard and vibration
should be felt when the engine oil control valve is oper-
ated.
(4) Turn the ignition switch to the "LOCK" (OFF) position.
Q: Is the engine oil control valve operating properly?
YES : Replace the engine oil pressure switch. Then go to
NO : Replace the engine oil control valve. Then go to Step
STEP 9. Using scan tool MB991958, read the diagnostic
trouble code (DTC).
(1) Turn the ignition switch to the "ON" position.
(2) Erase the DTC.
(3) Warm up the engine until engine coolant temperature
reaches 80
°C (176°F) or higher.
(4) 30 seconds or more have passed since the engine starting
sequence was completed, read the DTC.Turn the ignition
switch to the "LOCK" (OFF) position.
Q: Is DTC P1020 set?
YES : Replace the PCM. Then go to Step 10.
NO : The Inspection is complete.
AK303804AB
MB991910
DATA LINK
CONNECTOR
MB991824
MB991827
AK303804AB
MB991910
DATA LINK
CONNECTOR
MB991824
MB991827
MULTIPORT FUEL INJECTION (MFI) DIAGNOSIS
TSB Revision
MULTIPORT FUEL INJECTION (MFI) <2.4L ENGINE>
13A-853
STEP 10. Using scan tool MB991958, read the diagnostic
trouble code (DTC).
(1) Turn the ignition switch to the "ON" position.
(2) Erase the DTC.
(3) Warm up the engine until engine coolant temperature
reaches 80
°C (176°F) or higher.
(4) 30 seconds or more have passed since the engine starting
sequence was completed, read the DTC.Turn the ignition
switch to the "LOCK" (OFF) position.
Q: Is DTC P1020 set?
YES : Retry the trouble shooting.
NO : The Inspection is complete.
AK303804AB
MB991910
DATA LINK
CONNECTOR
MB991824
MB991827
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст