Mitsubishi Galant 9G. Manual — part 460
AUTO-CRUISE CONTROL
TSB Revision
ENGINE AND EMISSION CONTROL
17-58
STEP 4. Using scan tool MB991958, check data list item 07:
Transmission Range Switch.
CAUTION
To prevent damage to scan tool MB991958, always turn the
ignition switch to the "LOCK" (OFF) position before con-
necting or disconnecting scan tool MB991958.
(1) Connect scan tool MB991958 to the data link connector.
(2) Turn the ignition switch to the "ON" position.
(3) Set scan tool MB991958 to data reading mode for
auto-cruise control system. (Refer to
• Item 07, Transmission Range Switch.
• When selector lever is at the "P" or "N" position, the
display on scan tool MB991958 should be "ON".
• When selector lever is at the "R" or "D" position, the
display on scan tool MB991958 should be "OFF".
(4) Turn the ignition switch to the "LOCK" (OFF) position.
(5) Disconnect scan tool MB991958.
Q: Is the switch operating properly?
YES : Go to Step 5.
NO : Refer to
, Symptom Procedures
− Inspection
Procedure 2. Then go to Step 6.
STEP 5. Check the symptoms.
Q: Can auto-cruise control be set?
YES : It can be assumed that this malfunction is intermittent.
(Refer to GROUP 00, How to Use
Troubleshooting/Inspection Service Points
− How to
Cope with Intermittent Malfunction
NO : Replace the PCM. [Refer to GROUP 13A, Power
Control Module (PCM)
] <2.4L engine> or
[Refer to GROUP 13B, Power Control Module (PCM)
] <3.8L engine>. Then go to Step 6.
STEP 6. Check the symptoms.
Q: Can auto-cruise control be set?
YES : The procedure is complete.
NO : Return to Step 1.
AC305412
AB
MB991910
DATA LINK
CONNECTOR
MB991824
MB991827
AUTO-CRUISE CONTROL
TSB Revision
ENGINE AND EMISSION CONTROL
17-59
INSPECTION PROCEDURE 5: Hunting (Repeated Acceleration and Deceleration) Occurs at the Set
Vehicle Speed.
.
COMMENT
The output shaft speed sensor signal or the throttle
body is suspected.
.
TROUBLESHOOTING HINTS (THE MOST
LIKELY CAUSES FOR THIS CASE:)
• Malfunction of the output shaft speed sensor.
• Malfunction of the throttle body.
• Malfunction of the PCM.
DIAGNOSIS
Required Special Tools:
• MB991958: Scan Tool (MUT-III Sub Assembly)
• MB991824: V.C.I.
• MB991827: MUT-III USB Cable
• MB991910: MUT-III Main Harness A
STEP 1. Using scan tool MB991958, read the diagnostic
trouble code.
CAUTION
To prevent damage to scan tool MB991958, always turn the
ignition switch to the "LOCK" (OFF) position before con-
necting or disconnecting scan tool MB991958.
(1) Connect scan tool MB991958 to the data link connector.
(2) Turn the ignition switch to the "ON" position.
(3) Check for A/T system diagnostic trouble code. (Refer to
GROUP 23A, A/T Diagnosis
− Diagnostic Function − How
to Read and Erase Diagnostic Trouble Code
(4) Turn the ignition switch to the "LOCK" (OFF) position.
(5) Disconnect scan tool MB991958.
Q: Is any DTC set?
YES : Diagnose the A/T system. (Refer to GROUP 23A, A/T
Diagnosis
− Diagnostic Trouble Code Chart
NO : Go to Step 2.
AC305412
AB
MB991910
DATA LINK
CONNECTOR
MB991824
MB991827
AUTO-CRUISE CONTROL
TSB Revision
ENGINE AND EMISSION CONTROL
17-60
STEP 2. Using scan tool MB991958, read the diagnostic
trouble code.
CAUTION
To prevent damage to scan tool MB991958, always turn the
ignition switch to the "LOCK" (OFF) position before con-
necting or disconnecting scan tool MB991958.
(1) Connect scan tool MB991958 to the data link connector.
(2) Turn the ignition switch to the "ON" position.
(3) Check for MFI system diagnostic trouble code (Refer to
GROUP 13A, MFI Diagnosis
− Diagnostic Function − How
to Read and Erase Diagnostic Trouble Code
<2.4L engine> or (Refer to GROUP 13B, MFI Diagnosis
−
Diagnostic Function
− How to Read and Erase Diagnostic
) <3.8L engine>.
(4) Turn the ignition switch to the "LOCK" (OFF) position.
(5) Disconnect scan tool MB991958.
Q: Is any DTC set?
YES : Diagnose the MFI system. (Refer to GROUP 13A,
MFI Diagnosis
− Diagnostic Trouble Code Chart
) <2.4L engine> or (Refer to GROUP 13B,
MFI Diagnosis
− Diagnostic Trouble Code Chart
) <3.8L engine>. Then go to Step 4.
NO : Go to Step 3.
STEP 3. Retest the system
Q: Does hunting occur?
YES : Replace the PCM [Refer to GROUP 13A, Power
Control Module (PCM)
] <2.4L engine> or
[Refer to GROUP 13B, Power Control Module (PCM)
] <3.8L engine>. Then go to Step 4.
NO : It can be assumed that this malfunction is intermittent.
(Refer to GROUP 00, How to Use
Troubleshooting/Inspection Service Points
− How to
Cope with Intermittent Malfunction
STEP 4. Retest the system
Q: Does hunting occur?
YES : Return to Step 1.
NO : The procedure is complete.
AC305412
AB
MB991910
DATA LINK
CONNECTOR
MB991824
MB991827
AUTO-CRUISE CONTROL
TSB Revision
ENGINE AND EMISSION CONTROL
17-61
INSPECTION PROCEDURE 6: When "CRUISE" (MAIN) Switch is Turned "ON", "CRUISE" Indicator
Light Inside Combination Meter does not Illuminate. (However, Auto-cruise Control System is
Normal).
AC305714
IGNITION SWITCH (IG1)
JUNCTION
BLOCK
BLACK-
WHITE
COMBINATION
METER
RHEOSTAT
CIRCUIT
BLACK-
WHITE
RHEOSTAT
BLACK-
WHITE
BLACK
BLACK
BLACK
RED
BLACK-
YELLOW
BLACK
POWERTRAIN
CONTROL
MODULE (PCM)
BLACK
RED-
YELLOW
RED
RED
BATTERY
RELAY
BOX
WHITE
WHITE
RED-
WHITE
JOINT
CONNECTOR (1)
RED-
WHITE
RED-
WHITE
BLACK
RED
NOTE
WITHOUT ELECTRONIC BRAKE-FORCE
DISTRIBUTION (EBD) AND ANTI-LOCK
BRAKING SYSTEM (ABS)
WITH ELECTRONIC BRAKE-FORCE
DISTRIBUTION (EBD) AND ANTI-LOCK
BRAKING SYSTEM (ABS)
·
·
*
*
JOINT
CONNECTOR (2)
JOINT
CONNECTOR (3)
ABS-ECU OR
ABS/TCL-ECU
Auto-cruise Control Indicator Light Drive Circuit
AB
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст