Mitsubishi Galant 9G. Manual — part 295
MANUAL A/C DIAGNOSIS
TSB Revision
HEATER, AIR CONDITIONING AND VENTILATION
55A-256
12
A/C pressure sensor
Ignition switch: ON
5 V
13
− 15
−
−
−
16
Potentiometer power supply
Ignition switch: ON
5 V
17
Power transistor (BASE)
When the blower speed
selection dial shows Maximum
air volume.
1 V
18
Power transistor
(COLLECTOR)
When the blower speed
selection dial shows Maximum
air volume.
7.5 V
19
−
−
−
20
Sensors and potentiometers
ground
Always
0 V
21
Mode selection damper control
motor potentiometer input
When the damper has moved to
the DEF position.
0.7
− 1.3 V
22
−
−
−
23
Ambient air temperature sensor
input
When sensor temperature is
25
°C (77°F) [4 kΩ]
1.9 V
24
−
−
−
25
Air thermo sensor input
When sensor temperature is
25
°C (77°F) [1.5 kΩ]
2.2 V
26
A/C pressure sensor
at 2.6 MPa
3.9 V
27
Ground
Always
0 V
28
Power supply to the ignition
switch (IG2)
Ignition switch: ON
Battery positive voltage
29
Air mixing damper control motor
potentiometer input
When the damper door has
moved to the MAX. HOT
position.
0.7
− 1.3 V
30
Illumination ground
Always
0 V
31
ILL power supply
Lighting switch: ON
Battery positive voltage
32, 33
−
−
−
34
A/C pressure sensor ground
Always
0 V
36
Power supply to the ignition
switch (ACC)
Ignition switch: ON
Battery positive voltage
TERMINAL
NO.
CHECK ITEM
CHECKING REQUIREMENTS NORMAL CONDITION
SPECIAL TOOLS
TSB Revision
HEATER, AIR CONDITIONING AND VENTILATION
55A-257
SPECIAL TOOLS
M1552000600334
TOOL
TOOL NUMBER
AND NAME
SUPERSESSION
APPLICATION
MB991367
Special spanner
MB991367-01
Armature mounting nut of
compressor removal and
installation
MB991386 Pin
MIT217213
Armature mounting nut of
compressor removal and
installation
MB991658
Test harness set
Tool not available
Inspection of throttle position
sensor
B991367
MB991658
SPECIAL TOOLS
TSB Revision
HEATER, AIR CONDITIONING AND VENTILATION
55A-258
MB991958
A: MB991824
B: MB991827
C: MB991910
D: MB991911
E: MB991914
F: MB991825
G: MB991826
MUT-III Sub
Assembly
A: Vehicle
communicatio
n interface
(V.C.I.)
B: MUT-III USB
cable
C: MUT-III main
harness A
(Vehicles with
CAN
communicatio
n system)
D: MUT-III main
harness B
(Vehicles
without CAN
communicatio
n system)
E: MUT-III main
harness C (for
Daimler
Chrysler
models only)
F: MUT-III
measurement
adapter
G: MUT-III
Trigger
Harness
MB991824-KIT
NOTE: . G:
MB991826 MUT-III
Trigger Harness is not
necessary when
pushing V.C.I.
ENTER key.
Checking diagnostic trouble codes
CAUTION
For vehicles with CAN
communication, use MUT-III
main harness A to send
simulated vehicle speed. If you
connect MUT-III main harness B
instead, the CAN
communication does not
function correctly.
TOOL
TOOL NUMBER
AND NAME
SUPERSESSION
APPLICATION
MB991910
MB991826
MB991958
MB991911
MB991914
MB991824
MB991827
MB991825
DO NOT USE
A
B
C
D
E
F
G
DO NOT USE
ON-VEHICLE SERVICE
TSB Revision
HEATER, AIR CONDITIONING AND VENTILATION
55A-259
ON-VEHICLE SERVICE
REFRIGERANT LEVEL TEST
M1552008400408
Use the refrigerant recovery station to remove all of the refrig-
erant, and then calculate the amount of the refrigerant and
charge it.
A/C COMPRESSOR CLUTCH TEST
M1552019900032
1. Disconnect the air conditioning compressor clutch connector
to the air conditioning compressor clutch.
2. Connect positive battery voltage directly to the connector for
the air conditioning compressor clutch.
3. If the air conditioning compressor clutch is normal, there will
be a "click." If the pulley and armature do not make contact
("no click"), there is a malfunction.
SIMPLE INSPECTION OF THE A/C PRESSURE
SENSOR
M1552014700118
1. Assemble a gauge manifold on the high pressure service
valve.
2. Disconnect the A/C pressure sensor connector and connect
special tool test harness MB991658 as shown in the illustra-
tion.
3. Turn ON the engine and then turn ON the air conditioner
switch.
AC206292AB
A/C COMPRESSOR
CLUTCH
CONNECTOR
AC305034
A/C PRESSURE SENSOR
AD
AC307368
A/C
PRESSURE
SENSOR
SIDE
MB991658
AB
HARNESS SIDE
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст