Mitsubishi L200. Manual — part 597
TROUBLESHOOTING
SUPPLEMENTAL RESTRAINT SYSTEM (SRS)
52B-59
STEP 3. Check the harness for open circuit
between ignition switch and combination meter
connector C-112 (terminal No.36).
AC903856AR
Connector: C-112 <LHD>
Harness side
connector
(rear view)
AC903868
BD
Connector: C-112 <RHD>
Harness side
connector
(rear view)
NOTE:
AC903853
Connector: C-132 <LHD>
AC
C-132 (GR)
AC903865
Connector: C-132 <RHD>
AB
C-132 (GR)
AC509934 AS
Connectors: C-207, C-209 <LHD>
Harness side
C-209
C-207
Harness side
C-209
C-207
Junction block (Front view)
AC509936 AN
Connectors: C-207, C-209 <RHD>
Harness side
C-209
C-207
Harness side
C-209
C-207
Junction block (Front view)
Prior to the wiring harness inspection, check junction
block connector C-132, C-207 and C-209, and repair
if necessary.
Q: Is the check result normal?
YES :
An intermittent malfunction is suspected
(Refer to GROUP 00, How to Cope with
Intermittent Malfunction ).
NO :
Repair the harness wires between ignition
switch and the combination meter connector
C-112 (terminal No.36). Then go to Step 7.
TROUBLESHOOTING
SUPPLEMENTAL RESTRAINT SYSTEM (SRS)
52B-60
STEP 4. Check SRS-ECU connector C-131.
AC501670
AB
C-131 (Y)
Connector: C-131
Harness side
connector
(rear view)
Q: Is the connector correctly engaged?
YES :
Go to Step 5.
NO :
Engage the connector correctly. Then go to
Step 7.
STEP 5. Check the harness for short circuit
between the combination meter connector C-113
(terminal No.18) and SRS-ECU connector C-131
(terminal No.8).
AC903856BM
Connector: C-113 <LHD>
Harness side
connector
(rear view)
AC903868
CC
Connector: C-113 <RHD>
Harness side
connector
(rear view)
AC501670
AB
C-131 (Y)
Connector: C-131
Harness side
connector
(rear view)
Q: Is the check result normal?
YES :
Go to Step 6.
NO :
Repair the harness wires between the
combination meter connector C-113
(terminal No.18) and SRS-ECU connector
C-131 (terminal No.8). Then go to Step 7.
TROUBLESHOOTING
SUPPLEMENTAL RESTRAINT SYSTEM (SRS)
52B-61
STEP 6. Check the SRS warning lamp.
(1) Disconnect the negative battery terminal.
AC501670
AB
C-131 (Y)
Connector: C-131
Harness side
connector
(rear view)
(2) Disconnected the SRS-ECU connector C-131.
(3) Connect the negative battery terminal.
(4) Turn the ignition switch to the "ON" position.
Q: Does the SRS warning lamp illuminate?
YES :
Go to Step 7.
NO :
Replace the combination meter (Refer to
GROUP 54A, Combination Meter Assembly
). Go to Step 7.
STEP 7. Check whether the diagnosis code is
reset.
Check again if the diagnosis code is set.
(1) Erase the diagnosis code.
(2) Ignition: "LOCK" (OFF) position to "ON"
(3) On completion, check that the diagnosis code is
not reset.
Q: Is the diagnosis code set?
YES :
).
NO :
An intermittent malfunction is suspected
(Refer to GROUP 00, How to Cope with
Intermittent Malfunction ).
TROUBLESHOOTING
SUPPLEMENTAL RESTRAINT SYSTEM (SRS)
52B-62
Code No.B1551: SRS warning lamp circuit malfunction (Lamp does not Switch Off).
AC806011
Wire colour code
B : Black LG : Light green G : Green L : Blue W : White Y : Yellow SB : Sky blue
BR : Brown O : Orange GR : Grey R : Red P : Pink V : Violet PU : Purple
SRS Warning Lamp Drive Circuit
IGNITION
SWITCH (IG1)
COMBINATION
METER
SRS-ECU
AC
OPERATION
• Power for the SRS warning lamp is supplied from
the ignition switch (IG1) circuit.
• The SRS warning lamp illuminates when the igni-
tion switch is turned to the "ON" position and
goes out after approximately 7 seconds if there is
not a malfunction in the SRS system.
DIAGNOSIS CODE SET CONDITIONS
• This diagnosis code will be set if an open circuit
has occurred in the wiring harness between the
combination meter and the SRS-ECU.
TROUBLESHOOTING HINTS
• Damaged wiring harnesses of connectors
• Malfunction of the SRS-ECU
• Malfunction of the combination meter
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст