Mitsubishi L200. Manual — part 717
RADIO AND CD PLAYER
CHASSIS ELECTRICAL
54A-235
STEP 2. Connector check: radio and CD player
connector C-125.
Q: Is radio and CD player connector C-125 in good
condition?
YES :
Go to Step 3.
NO :
Repair or replace the component(s). If the
power switch is turned on, the radio and CD
player should operate normally.
STEP 3. Voltage measurement at radio and CD
player connector C-125 in order to check the
battery circuit of power supply system to the
radio and CD player (ignition switch ACC).
(1) Disconnect radio and CD player connector C-
125, and measure at the wiring harness side.
(2) Turn the ignition switch to "ACC" position.
(3) Measure the voltage between terminal 10 and
earth.
OK: System voltage
Q: Is the check result normal?
YES :
Go to Step 5.
NO :
Go to Step 4.
AC903856AE
Harness side
Connector: C-125 <LHD>
AC903868
AE
Harness side
Connector: C-125 <RHD>
AC903856AE
Harness side
Connector: C-125 <LHD>
AC903868
AE
Harness side
Connector: C-125 <RHD>
AC402679
Connector C-125
(Harness side)
BV
RADIO AND CD PLAYER
CHASSIS ELECTRICAL
54A-236
STEP 4. Check the wiring harness between radio
and CD player connector C-125 (terminal 10) and
ignition switch (ACC).
• Check the power supply line for open circuit and
short circuit.
NOTE:
Prior to the wiring harness inspection, check joint
connector C-127 and junction block connectors C-
207, C-208, and repair if necessary.
Q: Are the wiring harnesses between radio and CD
player connector C-125 (terminal 10) and ignition
switch (ACC) in good condition?
YES :
Refer to ignition switch (
NO :
Repair or replace the damage
component(s). If the power switch is turned
on, the radio and CD player should operate
normally.
AC903856AE
Harness side
Connector: C-125 <LHD>
AC903868
AE
Harness side
Connector: C-125 <RHD>
AC903853
Connector: C-127 <LHD>
AE
C-127 (GR)
AC903865
Connector: C-127 <RHD>
AD
C-127 (GR)
AC509934
Connectors: C-207, C-208 <LHD>
Junction block (Front view)
C-207
C-208
C-208
C-207
AB
Harness side
Harness side
AC509936
Connectors: C-207, C-208 <RHD>
C-207
C-208
C-207
Harness side
Harness side
C-208
AB
Junction block
(Front view)
RADIO AND CD PLAYER
CHASSIS ELECTRICAL
54A-237
STEP 5. Connector check: C-107 radio and CD
player connector
Q: Is the check result normal?
YES :
Go to Step 6.
NO :
Repair the defective connector.
STEP 6. Resistance measurement at C-107 radio
and CD player connector
(1) Disconnect the connector, and measure at the
wiring harness side.
(2) Check the continuity between C-107 radio and
CD player connector terminal No.41 and the body
earth.
OK: Continuity exists (2
Ω or less)
Q: Is the check result normal?
YES :
Go to Step 8.
NO :
Go to Step 7.
STEP 7. Check the harness wire between C-107
radio and CD player terminal No.41 and the body
earth
• Check the earth wires for open circuit.
Q: Is the check result normal?
YES :
Go to Step 8.
NO :
Repair the wiring harness.
AC903856AF
Harness side
Connector: C-107 <LHD>
C-107 (B)
AC903868
AF
Harness side
Connector: C-107 <RHD>
C-107 (B)
AC903856AF
Harness side
Connector: C-107 <LHD>
C-107 (B)
AC903868
AF
Harness side
Connector: C-107 <RHD>
C-107 (B)
AC310506JP
Connector C-107
(Harness side)
AC903856AF
Harness side
Connector: C-107 <LHD>
C-107 (B)
AC903868
AF
Harness side
Connector: C-107 <RHD>
C-107 (B)
RADIO AND CD PLAYER
CHASSIS ELECTRICAL
54A-238
STEP 8. Replace the radio and CD player
temporarily, and check the trouble symptom.
Replace the radio and CD player temporarily, and
check that the sound is output from the speaker.
Q: Is the check result normal?
YES :
Replace the radio and CD player.
NO :
Perform the diagnosis again. Go to Step 1.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст