Mitsubishi L200. Manual — part 564
WINDSHIELD WIPER AND WASHER
EXTERIOR
51-72
4. Check to see that the wiper motor runs at low
speed and then stops at the automatic stop
position.
WINDSHIELD WIPER AND WINDSHIELD
WASHER SWITCH CHECK
1
6
8
11
10
9
7
5
4
3
2
AC000417
Check continuity between the switch terminals.
Switch position
Tester
connection
Specified
condition
OFF
6
− 11, 6 − 10,
6
− 9, 6 − 8, 6
− 7
Open circuit
Windshield mist
wiper switch
6
− 11
Continuity
exists (2
Ω or
less)
Windshield
intermittent wiper
switch
6
− 10
Windshield low-
speed wiper
switch
6
− 9
Windshield high-
speed wiper
switch
6
− 8
Windshield
washer switch
6
− 7
WINDSHIELD INTERMITTENT WIPER
VOLUME CHECK
1
6
8
11
10
9
7
5
4
3
2
AC201004
Check that the resistance varies between 0 and 1 k
Ω
when the windshield intermittent volume is turned
from FAST to SLOW by after measuring resistance
between connector terminals 3 and 6 at the column
switch.
WINDSHIELD WIPER AND WASHER
EXTERIOR
51-73
WINDSHIELD WASHER
REMOVAL AND INSTALLATION
M1511008200838
AC500318
1
A
A
2
Section A – A
1
2
Claw
Claw
4
4.9 ± 0.7 N·m
11 ± 1.6 N·m
11 ± 1.6 N·m
11 ± 1.6 N·m
5
6
2
3
AB
Windshield washer nozzle removal
steps
•
Connection of windshield washer
hose
1. Windshield washer nozzle
Washer hose removal steps
•
Splash shield (LH) (Refer to GROUP
42, Fender .)
•
Connection of windshield washer
nozzle/washer tank
2. Windshield washer hose
Washer tank removal steps
•
Splash shield (LH) (Refer to GROUP
42, Fender .)
•
Connection of windshield washer
hose
3. Windshield washer tank
4. Washer tank filler cap
5. Washer tank filler hose
6. Windshield washer motor
Washer motor removal steps
•
Splash shield (LH) (Refer to GROUP
42, Fender .)
•
Connection of windshield washer
hose
6. Windshield washer motor
NOTE: For removal and installation of the wiper and
washer switch, refer to GROUP 54A, Column switch
.
Washer tank removal steps
WINDSHIELD WIPER AND WASHER
EXTERIOR
51-74
INSPECTION
M1511008300813
WINDSHIELD WASHER MOTOR CHECK
1 2
AC502772
1. Remove the washer tank assembly with the
washer hose connected. Then fill the washer tank
with water.
2. Check to see that the water is vigorously sprayed
when connecting the terminals as shown in the
illustration.
WINDSHIELD WASHER SWITCH CHECK
<LH DRIVE VEHICLES>
AC605524
1
6
8
11
10
9
7
5
4
3
2
AD
<RH DRIVE VEHICLES>
Check the windshield washer switch from the ETACS
diagnosis codes for proper operation (Refer to
GROUP 54A, ETACS ).
WINDSHIELD WASHER FLUID EJECTION
CHECK
Switch position
Tester
connection
Specified
condition
OFF
6
− 7
Open circuit
Windshield washer
switch ON
6
− 7
Continuity exists
(2
Ω or less)
NOTE: Be sure to use the special tool, washer noz-
zle adjustment tool (MB992326) to adjust the splash-
ing points of the nozzle.
AC900637
AC
MB992326
Mist type
washer nozzle adjusting side
Jet type washer nozzle
adjusting side
ADJUSTMENT OF THE JET TYPE WASHER
NOZZLE INJECTION POSITION
CAUTION
Adjust the splashing position within the speci-
fied adjustment range, otherwise the windshield
glass cannot be washed properly.
1. Use the special tool, washer nozzle adjustment
tool (MB992326) to adjust the splashing points of
the nozzle.
AC900640
AB
MB992326
Jet type
washer nozzle
adjusting side
Jet type
washer
nozzle
B
(A)
2. Insert the jet type washer nozzle adjusting side of
the special tool (MB992326) into the injection part
of the washer nozzle as shown in figure (A).
AC900643
AC
MB992326
Jet type washer nozzle
adjusting side
Jet type
washer nozzle
(B)
WINDSHIELD WIPER AND WASHER
EXTERIOR
51-75
3. Move the special tool (MB992326) up and down
to adjust the angle of the washer nozzle as shown
in figure (B).
ACA01207 AB
50
50
50
115
70
20
70
50
365
<Right>
<Left>
Windshield ceramic
line end
Unit: mm
Windshield washer
nozzle perpendicular
115
210
180
365
Windshield washer nozzle
210
180
20
LIGHTING CONTROL SENSOR
LIGHTING CONTROL SENSOR REMOVAL AND INSTALLATION
M1511028300064
For removal and installation, refer to GROUP 54A,
Lighting control sensor .
Lighting control sensor (rain sensor)
adaptation
M1511028600106
CAUTION
• Before performing the adaptation, check if the
lighting control sensor (rain sensor)-related
diagnosis code is set in the lighting control
sensor (rain sensor).
• Turn the wiper switch to the OFF position.
1. Clean the windshield in fine weather.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст