Mitsubishi L200. Manual — part 563
Function
Item name
Configuration
Windshield wiper intermittent control
(vehicle speed sensing intermittent time
adjustable type)
Vehicle speed-
dependent wiper
• Inhibit
• Operation (initial condition)
Wiper linked with washer function
Wiper synchronized
washer
• Inhibit
• Operation (initial condition)
WINDSHIELD WIPER AND WASHER
EXTERIOR
51-68
WINDSHIELD WIPER
REMOVAL AND INSTALLATION
M1511007900522
AC509729
1
2
8
3
6
5
4
AB
27 ± 3 N·m
8.0 ± 2 N·m
8.0 ± 2 N·m
8.0 ± 2 N·m
27 ± 3 N·m
B
5
7
N
A
View A
7
Specified grease:
Multipurpose grease
SAE J310, NLGI No.2 or equivalent
AC509856 AB
View B
NOTES
C
C
: Clip <a> positions
: Claw positions
: Clip <b> positions
Section C – C
Section D – D
4
Clip <a>
Claw
Hood
4
5
5
Hood
Clip <a>
Clip <b>
D
D
Wiper blade removal steps
1. Wiper blade assembly
>>
C
<< 2. Wiper blade
Windshield wiper motor and link
assembly removal steps
>>
B
<< 3. Wiper arm
4. Hood weather strip
5. Front deck garnish
<<
A
>> >>
A
<< 6. Windshield wiper link
<<
A
>> >>
A
<< 7. Wiper motor link plate
<<
A
>> >>
A
<< 8. Windshield wiper motor
WINDSHIELD WIPER AND WASHER
EXTERIOR
51-69
NOTE: For removal and installation of the wiper and
washer switch, refer to GROUP 54A, Column switch
.
REMOVAL SERVICE POINT
<<A>> WINDSHIELD WIPER LINK/WIPER MOTOR
LINK PLATE/WINDSHIELD WIPER MOTOR
REMOVAL
AC509804AB
Wiper motor link plate
1. To disconnect the wiper motor link plate from the
wiper motor shaft, use an appropriate tool to
counter-hold the plate to prevent it from turning.
2. Remove the wiper motor from the windshield
wiper link.
INSTALLATION SERVICE POINT
>>A<< WINDSHIELD WIPER LINK/WIPER MOTOR
LINK PLATE/WINDSHIELD WIPER MOTOR
INSTALLATION
1. Confirm that the wiper motor has set to automatic
stop position (refer to
).
AC509805AB
Wiper link rod plate
(incorrect location)
Wiper link rod plate (correct location)
CAUTION
Wiper link rod plate at left end should be located
as shown in the illustration (dotted line shows
incorrect location).
2. Assemble the wiper motor to windshield wiper
link.
AC509806AC
Wiper motor link plate
Link rod
Within ± 3˚
WINDSHIELD WIPER AND WASHER
EXTERIOR
51-70
CAUTION
Always replace the wiper motor link plate with
new one.
3. Set the wiper motor link plate onto the wiper motor
shaft; aligning the plate to the windshield wiper
link as shown in the illustration.
4. Tighten the attaching nut of wiper motor link plate
and wiper motor shaft. Use an appropriate tool to
counter-hold the plate to prevent it from turning.
5. Apply grease to the inside of link rod joint (as
required) and connect the link rod to wiper motor
link plate.
>>B<< WIPER ARM INSTALLATION
AC509858AB
Front deck garnish
Front deck garnish
Front deck garnish
Section A – A
Section B – B
A
A
B
B
(33 ± 5 mm)
(31 ± 5 mm)
Marking (small circle on windshield)
Align blade to
marking on
windshield
Align blade to
marking on
windshield
Install the wiper arms and blades at the specified
positions shown above.
WINDSHIELD WIPER AND WASHER
EXTERIOR
51-71
>>C<< WIPER BLADE INSTALLATION
AC103612
AD
Backing
Backing
A
A
Section A – A
Wiper blade
Backing
Wiper blade
Backing
Backing
A
A
<Passenger's side>
<Driver's side>
Wiper blade
CAUTION
For good windshield wiper wiping performance,
use a driver's side windshield wiper without
curve in the backings of the wiper blade. The
windshield wiper on the passenger's side should
be a wiper blade with curved backings.
INSPECTION
M1511008000500
WINDSHIELD WIPER MOTOR CHECK
Inspect the windshield wiper motor by removing the
harness connector with the motor attached to the
vehicle.
WIPER MOTOR AT LOW OR HIGH SPEED
OPERATION
1
4
2
3
5
4
2
3
5
1
1
4
2
3
5
AC509860
Check operation
Low speed
High speed
AB
Connect the battery to the wiper motor to inspect the
operation of motor rotation at low or high speed.
WIPER MOTOR AT STOP POSITION OPERATION
1
4
2 3
5
4
2 3
5
1
4
2
3
5
1
AC509861
Stop position check
(B) Automatic stop
(A) Low speed
AB
1. Connect the battery to the wiper motor as shown
in the illustration (A).
2. Run the wiper motor at low speed, then
disconnect the battery in the middle of the motor
rotation and check to see that the motor stops.
3. As shown in the illustration (B), connect the
terminals of the wiper motor connector.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст