Mitsubishi L200. Manual — part 408
GENERAL INFORMATION
REAR SUSPENSION
34-2
GENERAL INFORMATION
M1341000101914
The leaf spring type rear suspension featuring the
simple structure and outstanding strength has been
adopted.
• The spring is fixed at the top to increase ground
clearance of the leaf spring. <2WD (High rider),
4WD>
• The suspension geometry has been optimized to
assure stability under loaded condition and to
improve adhesion under unladen condition, and
the SUV-like steering stability has been achieved.
<2WD (High rider), 4WD>
CONSTRUCTION DIAGRAM
<2WD (except High rider)>
AC501757
U-bolt
Bump stopper
Shock absorber
Leaf spring
AB
<2WD (High rider), 4WD>
AC808337
U-bolt
Bump stopper
Shock absorber
Leaf spring
AB
REAR SUSPENSION ASSEMBLY
REAR SUSPENSION
34-3
REAR SUSPENSION ASSEMBLY
REMOVAL AND INSTALLATION
M1341001000359
CAUTION
•
Pre-installation Operation
• Support the axle housing with a garage jack etc..
*
: Indicates parts which should be temporarily tightened, and then fully tightened with the vehicle
on the earth in the unladen condition.
<2WD (EXCEPT HIGH RIDER)>
AC501835AB
105 ± 10 N·m*
10
108 ± 10 N·m
52 ± 7 N·m*
8
6
7
4
2
1
22 ± 3 N·m*
22 ± 3 N·m*
5
3
9
8
REAR SUSPENSION ASSEMBLY
REAR SUSPENSION
34-4
<2WD (HIGH RIDER), 4WD>
AC808360AD
2
1
105 ± 10 N·m*
8
6
7
3
5
4
10
9
108 ± 10 N·m
<Except 4WD - RHD>
52 ± 7 N·m*
22 ± 3 N·m*
22 ± 3 N·m*
88 ± 8 N·m
<4WD - RHD>
Removal steps
1.
Parking brake cable attaching bolt
>>
C
<< 2.
Shock absorber
3.
U-bolt seat
>>
B
<< 4.
U-bolts
5.
Bump stopper
•
Spare tyre (LH only)
6.
Shackle plate
>>
A
<< 7.
Shackle assembly
8.
Rubber bushings
>>
A
<< 9.
Bolt
10. Rear spring
INSTALLATION SERVICE POINTS
>>A<< BOLT/SHACKLE ASSEMBLY INSTALLA-
TION
AC501428
Inside of vehicle
Inside of vehicle
AB
Bolt side
Shackle side
1. Install the bolt from the outside toward the inside
of vehicle.
2. Install the shackle assembly from the inside
toward the outside of vehicle.
REAR SUSPENSION ASSEMBLY
REAR SUSPENSION
34-5
>>B<< U-BOLTS INSTALLATION <2WD (HIGH
RIDER), 4WD>
ACB00222
Approximately
3 mm max
AB
U-bolt
U-bolt seat
Install the u-bolts as shown in the figure.
>>C<< SHOCK ABSORBER INSTALLATION
AC702929AB
Inner
washer
Outer
washer
Be sure to install the shock absorber washers (outer
and inner) in the specified direction.
INSPECTION
M1341015500175
• Check the rubber parts for cracks and wear.
• Check the shock absorber for malfunction, oil
leakage, or abnormal noise.
• Check the leaf springs for damage or deteriora-
tion.
• Check the U-bolt for cracks or bends.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст