Mitsubishi L200. Manual — part 206
FUEL FILTER
FUEL SUPPLY
13B-6
FUEL FILTER
REMOVAL AND INSTALLATION <Vehicles with steel fuel filter case>
M1135002800559
Post-installation Operation
• Evacuation of Air from Fuel Line (Refer to GROUP 13A −
On-vehicle Service, Evacuation of Air from Fuel Line ).
AC807196
5
1
6
2
12 ± 2 N·m
N
AB
1
6.0 ± 1.0 N·m
0.6 ± 0.2 N·m
4
3
N
7
N
5.0 ± 1.0 N·m
Removal steps
>>
B
<<
1.
Fuel line hose connection
2.
Fuel filter assembly
3.
Fuel line plug (drain plug)
4.
Water level switch
<<
A
>>
>>
A
<<
5.
Fuel filter
6.
Fuel filter pump
7.
Fuel line plug (air plug) and O-
ring
REMOVAL SERVICE POINT
<<A>> FUEL FILTER REMOVAL
AC502833AB
Fix the fuel filter body to a vice, and then remove the
fuel filter using an oil filter wrench.
INSTALLATION SERVICE POINTS
>>A<< FUEL FILTER INSTALLATION
1. Clean the mounting surface on the fuel filter body
side.
FUEL FILTER
FUEL SUPPLY
13B-7
2. Tighten the fuel filter to the specified torque from
the point where the gasket contacts the mounting
surface.
Tightening torque: Approximately 3/4
− 1
turn (12
± 2 N⋅m)
>>B<< FUEL LINE HOSE INSTALLATION
AC503372 AB
20 – 25 mm
If the pipe has a stepped part, connect securely up to
the stepped part. If the pipe has no stepped part,
insert so that the inserted portion 20
− 25 mm long.
FUEL FILTER
FUEL SUPPLY
13B-8
REMOVAL AND INSTALLATION <Vehicles with plastic fuel filter case>
M1135002800560
Post-installation Operation
• Evacuation of Air from Fuel Line (Refer to GROUP 13A −
On-vehicle Service, Evacuation of Air from Fuel Line ).
ACB01919AB
11 ± 2 N·m
11 ± 2 N·m
11 ± 2 N·m
1
9
8
6
5
4
3
2
N
N
7
N
Fuel filter removal steps
1.
Fuel filter protector B
<<
A
>>
>>
A
<<
5.
Fuel filter cap
6.
Fuel filter and O-ring
7.
O-ring
Removal steps
1.
Fuel filter protector B
>>
B
<<
2.
Fuel line hose C connection
>>
B
<<
3.
Fuel line hose B connection
4.
Fuel line plug (drain plug) and O-
ring
<<
B
>>
>>
A
<<
5.
Fuel filter cap
6.
Fuel filter and O-ring
7.
O-ring
8.
Fuel filter case
•
Glow plug control relay and
bracket (Refer to GROUP 16
−
Glow System, Glow Plug Relay )
9.
Fuel filter protector A
REMOVAL SERVICE POINTS
<<A>> FUEL FILTER CAP REMOVAL
1. Loosen the drain plug to drain the fuel. Then,
tighten the drain plug.
Removal steps (Continued)
ACB01912
Fastener
nut
AB
FUEL FILTER
FUEL SUPPLY
13B-9
2. Insert a flat-tipped screwdriver into the groove of
the fastener nut.
3. Loosen the fastener nut using the flat-tipped
screwdriver until it can be loosened by hand.
<<B>> FUEL FILTER CAP REMOVAL
ACB01912
Fastener
nut
AB
1. Insert a flat-tipped screwdriver into the groove of
the fastener nut.
2. Loosen the fastener nut using the flat-tipped
screwdriver until it can be loosened by hand.
INSTALLATION SERVICE POINTS
>>A<< FUEL FILTER CAP INSTALLATION
ACB01913
1. Install the fuel filter cap by aligning the marks on
the fuel filter cap and the fuel filter case.
O P E N
ACB01914AB
Mark
2. Securely tighten the fastener nut until the mark is
in the position shown in the figure (until it clicks in
place).
>>B<< FUEL LINE HOSE CONNECTION
ACB02187AB
Under 2 mm
Securely insert the fuel line hose to the fuel filter and
install the hose clip in the position shown in the fig-
ure.
INSPECTION
M1135002900233
<Vehicles with steel fuel filter case>
WATER LEVEL SWITCH CHECK
1. Connect the circuit tester to the water level switch.
1 2
AC502835 AC
Float
2. There should be continuity when the float is
raised, while there is no continuity when it is
lowered.
3. Replace the fuel filter assembly if it is faulty.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст