Mitsubishi L200. Manual — part 422
TROUBLESHOOTING
ANTI-SKID BRAKING SYSTEM (ABS)
35B-9
ABS WARNING LAMP AND BRAKE
WARNING LAMP CHECK
M1352012000799
Check that ABS and brake warning lamps illuminate
as follows.
NOTE: The EBD warning lamp is also used as the
brake warning lamp.
AC506224AB
Approx. 3 s
Warning
lamp
Ignition
switch
Illuminated
Not
illuminated
START
ON
ACC
ABS warning lamp
Brake warning lamp
1. When the ignition switch is turned to the ON
position, ABS and brake warning lamps illuminate.
2. The ABS and brake warning lamps illuminate for
three seconds
*1
and then turn OFF
*2
.
3. Otherwise, check the diagnosis code.
NOTE:
.
•
*1
: The ABS warning lamp may stay ON until the
vehicle speed reaches 10 km/h. As far as ABS-
ECU stores any diagnosis code related to the
wheel speed sensor malfunction or the motor
malfunction as past trouble, ABS-ECU continues
illuminating the ABS warning lamp until it verifies
that the malfunction for that code is resolved
(startup check).
•
*2
: The brake warning lamp does not turn OFF
when the parking brake is applied or the brake
fluid level is lowered.
DIAGNOSIS FUNCTION
M1352011201696
ABS-ECU has the following functions for easier sys-
tem checks. The following items can be diagnosed
using M.U.T-III.
• Diagnosis code set (Refer to
• Service data output (Refer to
).
• Actuator test (Refer to
CHECK OF FREEZE FRAME DATA
To detect fault and store the diagnosis code, the
ABS-ECU obtains data before the confirmation of the
diagnosis code and data when the diagnosis code is
confirmed, and then stores the current condition of
the ABS-ECU. By analysing each data from M.U.T.-
III, the troubleshooting can be performed more effi-
ciently. Display items of the freeze frame data are as
follows.
TROUBLESHOOTING
ANTI-SKID BRAKING SYSTEM (ABS)
35B-10
Display item list
Item No.
Item name
Data item
Unit
02
Ignition cycle
Number of times the ignition switch is turned
"ON" or "LOCK (OFF)" after the past failure
transition.
Number of
counts is
displayed.
03
Elapsed time
Total elapsed time after a diagnosis code is
generated
min
*
04
Accumulated minute
Cumulative time for current malfunction of
diagnosis code
min
NOTE:
*
: Total elapsed time can be stored up to
65534 minutes. The display of M.U.T.-III is fixed to
65534 minutes after 65534 minutes have elapsed.
Or, if the battery is disconnected, the total elapsed
time cannot be measured properly. Thus, 65535 min-
utes (null value) is displayed. Since the value is cal-
culated according to the information from the ABS-
ECU, a proper value may not be displayed when the
ABS-ECU time-out has occurred.
FAIL-SAFE FUNCTION
If any malfunction is detected by the self-diagnostic
function, ABS-ECU illuminates the ABS warning
lamp and brake warning lamp
*
, and it disables ABS
and EBD control.
NOTE: *: The brake warning lamp is used as EBD
control warning lamp.
Illumination condition of warning lamp in case of failure
Diagnosis
code No.
Item
Countermeasures for failure
Brake warning lamp ABS warning lamp
C1200
Wheel speed sensor
(FR)
Signal open circuit
Extinguished
*1
Illuminated
*2
Illuminated
C1205
Wheel speed sensor
(FL)
Signal open circuit
C1210
Wheel speed sensor
(RR)
Signal open circuit
C1215
Wheel speed sensor
(RL)
Signal open circuit
C1201
Wheel speed sensor
(FR)
Signal short circuit
Extinguished
*1
Illuminated
*2
Illuminated
C1206
Wheel speed sensor
(FL)
Signal short circuit
C1211
Wheel speed sensor
(RR)
Signal short circuit
C1216
Wheel speed sensor
(RL)
Signal short circuit
TROUBLESHOOTING
ANTI-SKID BRAKING SYSTEM (ABS)
35B-11
C1202
Wheel speed sensor
(FR)
Malfunction power
circuit
Extinguished
*1
Illuminated
*2
Illuminated
C1207
Wheel speed sensor
(FL)
Malfunction power
circuit
C1212
Wheel speed sensor
(RR)
Malfunction power
circuit
C1217
Wheel speed sensor
(RL)
Malfunction power
circuit
C1225
*3
Wheel speed sensor
malfunction
Abnormality in tyre size
Extinguished
Illuminated
C1226
Control solenoid valve (FR) pressure holding
system
Illuminated
Illuminated
C1236
Control solenoid valve (FL) pressure holding
system
C1246
Control solenoid valve (RR) pressure holding
system
C1256
Control solenoid valve (RL) pressure holding
system
C1231
Control solenoid valve (FR) pressure reducing
system
Illuminated
Illuminated
C1241
Control solenoid valve (FL) pressure reducing
system
C1251
Control solenoid valve (RR) pressure reducing
system
C1261
Control solenoid valve (RL) pressure reducing
system
C1266
*4
Motor malfunction
Motor stick or open
circuit
Illuminated
Illuminated
C1273
*4
Motor relay
malfunction
Open circuit
Illuminated
Illuminated
C1274
Motor relay
malfunction
Short circuit
Illuminated
Illuminated
C1278
Valve relay malfunction Open circuit
Illuminated
Illuminated
C1279
Valve relay malfunction Short circuit
Illuminated
Illuminated
C1340
Stop lamp switch
malfunction
Short circuit (short to
power supply)
Extinguished
Illuminated
C1365
*5
G-sensor malfunction
Power supply error
Extinguished
Illuminated
C1381
*5, *6
G-sensor malfunction
Abnormal seizure or
output error
Extinguished
Illuminated
C1382
*5
G-sensor malfunction
Low voltage
Extinguished
Illuminated
C1383
*5
G-sensor malfunction
High voltage
Extinguished
Illuminated
Diagnosis
code No.
Item
Countermeasures for failure
Brake warning lamp ABS warning lamp
TROUBLESHOOTING
ANTI-SKID BRAKING SYSTEM (ABS)
35B-12
NOTE:
.
•
*1
: Normality on rear wheels (both right or left)
•
*2
: Abnormality on rear wheels (both right and left)
•
*3
: This diagnosis code is not set within the vehicle speed of 30 km/h or less.
•
*4
: This diagnosis code is not set within the vehicle speed of 10 km/h or less.
•
*5
: 4WD
•
*6
: This diagnosis code is not set within the vehicle speed of 30 km/h or less.
Under EBD and ABS control in case of failure
C1860
ABS-ECU power
supply system
malfunction
high voltage
Illuminated
Illuminated
C1861
ABS-ECU power
supply system
malfunction
Low voltage
Illuminated
Illuminated
C1395
Brake fluid charging incompletion
Flashes
Flashes
U1073
Trouble in CAN bus system
Extinguished
Extinguished
Diagnosis
code No.
Item
Countermeasures for failure
Brake warning lamp ABS warning lamp
Diagnosis
code No.
Item
Countermeasures for failure
EBD control
ABS control
C1200
Wheel speed sensor
(FR)
Open circuit
Executed
*1
Prohibited
*2
Prohibited
C1205
Wheel speed sensor
(FL)
Open circuit
C1210
Wheel speed sensor
(RR)
Open circuit
C1215
Wheel speed sensor
(RL)
Open circuit
C1201
Wheel speed sensor
(FR) system
Short circuit
Executed
*1
Prohibited
*2
Prohibited
C1206
Wheel speed sensor
(FL) system
Short circuit
C1211
Wheel speed sensor
(RR) system
Short circuit
C1216
Wheel speed sensor
(RL) system
Short circuit
C1202
Wheel speed sensor
(FR)
Malfunction power
circuit
Executed
*1
Prohibited
*2
Prohibited
C1207
Wheel speed sensor
(FL)
Malfunction power
circuit
C1212
Wheel speed sensor
(RR)
Malfunction power
circuit
C1217
Wheel speed sensor
(RL)
Malfunction power
circuit
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст