Mitsubishi L200. Manual — part 231
ACA01401
Connector: C-105 <LH drive vehicles>
AC
C-105 (B)
ACA01402
Connector: C-105 <RH drive vehicles>
AC
C-105 (B)
ACA01405
Connector: C-111 <LH drive vehicles>
AD
ACA01406 AD
Connector: C-111 <RH drive vehicles>
CRUISE CONTROL
ENGINE AND EMISSION CONTROL
17-28
OPERATION
The engine-ECU detects "ON/OFF" switch ON signal
to illuminate the cruise control indicator lamp on the
combination meter.
COMMENT
The combination meter or engine-ECU may also be
defective.
PROBABLE CAUSE
• Damaged harness or connector.
• Malfunction of the combination meter.
• Malfunction of the engine-ECU.
DIAGNOSIS PROCEDURE
STEP 1. Check the cruise control indicator lamp.
(1) Disconnect engine-ECU connector C-105 and
check at the harness side connector.
(2) Turn the ignition switch to the "ON" position.
(3) Check the illumination condition of the cruise
control indicator lamp when engine-ECU
connector C-105 terminal No.45 is earthed.
OK: The cruise control indicator lamp
illuminates.
Q: Is the check result normal?
YES :
Go to Step 5.
NO :
Go to Step 2.
STEP 2. Connectors check: C-111 combination
meter connector, C-105 engine-ECU connector
and C-53 <LHD> or C-35 <RHD> intermediate
connector.
Q: Is the check result normal?
YES :
Go to Step 3.
NO :
Repair or replace the damaged connector.
Then go to Step 6.
STEP 3. Check the harness wire between
combination meter connector C-111 terminal
No.53 and engine-ECU connector C-105 terminal
No.45.
• Check harness wire for open/short circuit and
damage.
Q: Is the check result normal?
YES :
Go to Step 4.
NO :
Repair or replace the damaged harness
wire. Then go to Step 6.
STEP 4. Check the combination meter.
Refer to GROUP 54A
− Combination Meter, Trouble-
shooting, Check at ECU Terminals .
Q: Is the check result normal?
YES :
Go to Step 5.
NO :
Replace the combination meter (Refer to
GROUP 54A
− Combination Meter ). Then
go to Step 6.
CRUISE CONTROL
ENGINE AND EMISSION CONTROL
17-29
STEP 5. Check the symptom.
Q: When the "ON/OFF" switch is turned ON, is the
cruise control indicator lamp illuminated?
YES :
It can be assumed that this malfunction is
intermittent (Refer to GROUP 00
− How to
Use Troubleshooting/Inspection Service
Points, How to Cope with Intermittent
Malfunctions ).
NO :
Replace the engine-ECU (Refer to GROUP
13A
− Engine-ECU ). Then go to Step 6.
STEP 6. Check the symptom.
Q: When the "ON/OFF" switch is turned ON, is the
cruise control indicator lamp illuminated?
YES :
The procedure is complete.
NO :
Return to Step 1.
DATA LIST REFERENCE TABLE
M1172002401980
CAUTION
• Road test always need two people: one driver and one observer.
• When shifting the selector lever to "D" position the brakes should be applied so that the vehicle
does not move forward.
NOTE: When reading the data list, do not select the
item under "CRUISE CONTROL," but select the item
under "DIESEL ENGINE."
Item No. Check item
Check condition
Normal condition
04
Vehicle speed sensor Road test the vehicle.
The speedometer and
M.U.T.-III display the
same value.
42
Inhibitor switch <A/T> Ignition switch:
"ON"
Selector lever: "N" or "P" position ON
Selector lever: Other than "N" or
"P" position
OFF
130
Cancel code
Ignition switch: "ON"
The cancel code,
which set when the
cruise control system
was cancelled at the
last time, is set again.
131
Clutch switch <M/T>
Ignition switch:
"ON"
Clutch pedal: Depressed
ON
Clutch pedal: Released
OFF
134
Brake switch (for
cruise control circuit)
Ignition switch:
"ON"
Brake pedal: Depressed
ON
Brake pedal: Released
OFF
135
Stop lamp switch (for
stop lamp circuit)
Ignition switch:
"ON"
Brake pedal: Depressed
ON
Brake pedal: Released
OFF
136
Cruise control switch
("ON/OFF" switch)
Ignition switch:
"ON"
"ON/OFF" switch: Pushed
ON
"ON/OFF" switch: Pushed again OFF
137
Cruise control switch
("CANCEL" switch)
Ignition switch:
"ON"
"CANCEL" switch: Pushed
ON
"CANCEL" switch: Released
OFF
138
Cruise control switch
("COAST/SET"
switch)
Ignition switch:
"ON"
"COAST/SET" switch: Pushed
ON
"COAST/SET" switch: Released OFF
139
Cruise control switch
("ACC/RES" switch)
Ignition switch:
"ON"
"ACC/RES" switch: Pushed
ON
"ACC/RES" switch: Released
OFF
140
Cruise control
operation
Cruise control system: active
ON
Cruise control system: Inactive
OFF
CRUISE CONTROL
ENGINE AND EMISSION CONTROL
17-30
CHECK AT ENGINE-ECU TERMINAL
M1172002701936
Use special tool power plant ECU check harness
(MB992291), check the engine-ECU terminal volt-
age.
1. Remove the engine-ECU (Refer to GROUP 13A
−
Engine-ECU ).
2. Connect special tool MB992291 between the
engine-ECU and the body-side harness
connector.
3. Measure the voltages between the check
connector terminals of special tool MB992291 and
earth terminals No.116, 117 or 145.
AC809546
35
40
41
42
1817
38
39
15
16
14
3736
12
13
11
32
8
3433
9
10
30
31
7 6
29
5
4
28
3
27
2
26
1
25
19
43
2120
22
23
46
47
4544
24
48
76
52
86
62
63
64
65
66
67
68
69
70
71
72
92
95
96
93
94
89
90
91
8887
53
54
55
56
57
58
59
60
61
83
8584
8281
78
79
80
77
49
50
51
74
75
73
125
110
122
107
108
123
109
124
128
113
111
126
112
127
129
114
115
130
119
104
120
105
121
106
118
103
102 101
117 116
151
142
157
158
143
154
156
141
155
140
138
153
139
152
137
146
135
150
136
149
134
132
147
148
133
131
145 144
AE
Special tool - Power plant ECU check harness (MB992291) connector
58-Pin connector
(Engine-ECU connector C-103)
96-Pin connector
(Engine-ECU connector C-105)
Terminal No. Check item
Check condition
Normal condition
7 <Except
EURO 5>
Stop lamp switch
(brake switch)
Ignition switch:
"ON"
Depress the brake pedal.
System voltage
Release the brake pedal.
1V or less
112
Clutch switch
<M/T>
Ignition switch:
"ON"
Release the clutch pedal.
10 V or more
Depress the clutch pedal.
1 V or less
125
Stop lamp switch Ignition switch:
"ON"
Depress the brake pedal.
System voltage
Release the brake pedal.
1V or less
126 <EURO
5>
Stop lamp switch
(brake switch)
Ignition switch:
"ON"
Depress the brake pedal.
System voltage
Release the brake pedal.
1V or less
139
Cruise control
switch power
supply
Ignition switch:
"ON"
All switches: Released
4.7
− 5.0 V
"ON/OFF" switch: Pushed.
0
− 0.5 V
"CANCEL" switch: Pushed.
1.0
− 1.8 V
"COAST/SET" switch: Pushed.
2.3
− 3.0 V
"ACC/RES" switch: Pushed.
3.5
− 4.2 V
ON-VEHICLE SERVICE
CRUISE CONTROL SWITCH CHECK
M1172001201295
CRUISE CONTROL "ON/OFF" SWITCH
CHECK
1. Turn the ignition switch to "ON" position.
AC807212
"ON/OFF"
switch
AC
Cruise control switch
AC900932
Cruise control
indicator lamp
AB
CRUISE CONTROL
ENGINE AND EMISSION CONTROL
17-31
2. Push the "ON/OFF" switch of the cruise control
switch, and check that the cruise control indicator
lamp within the combination meter illuminates.
3. Push the "ON/OFF" switch again, and check that
the cruise control indicator lamp within the
combination meter goes out.
CRUISE CONTROL SETTING
1. Turn the ignition switch to "ON" position.
2. Push the "ON/OFF" switch (cruise control system:
ON, cruise control indicator lamp: illuminated).
3. Drive at the desired speed within the range of
approximately 40
− 200 km/h.
AC807212
"COAST/SET"
switch
AD
Cruise control switch
4. Push the "COAST/SET" switch.
5. Check to be sure that when the "COAST/SET"
switch is released the speed is the desired
constant speed.
NOTE: If the vehicle speed decreases to approxi-
mately 15 km/h below the set speed because of
climbing a hill for example, it is normal for the
cruise control to be cancelled. When the vehicle
speed is decelerated to the low speed limit
(approximately 40 km/h) or less, the constant
speed driving will be cancelled even if the vehicle
speed is not decelerated 15 km/h or more from
the set speed.
SPEED-INCREASE SETTING
1. Turn the ignition switch to "ON" position.
2. Push the "ON/OFF" switch (cruise control system:
ON, cruise control indicator lamp: illuminated).
3. Set to the desired speed within the range of
approximately 40
− 200 km/h.
AC807212 AE
Cruise control switch
"ACC/RES"
switch
4. Push the "ACC/RES" switch.
5. Check to be sure that acceleration continues
while the "ACC/RES" switch is pushed, and that
the speed at the time it was released becomes the
constant driving speed.
NOTE: When the vehicle speed reaches the high
speed limit (approximately 200 km/h) during
acceleration, the vehicle is driven at a constant
speed of the high speed limit (approximately 200
km/h).
SPEED-REDUCTION SETTING
1. Turn the ignition switch to "ON" position.
2. Push the "ON/OFF" switch (cruise control system:
ON, cruise control indicator lamp: illuminated).
3. Set to the desired speed within the range of
approximately 40
− 200 km/h.
4. Press the "COAST/SET" switch.
5. Check to be sure that deceleration continues
while the "COAST/SET" switch is pushed, and
that the speed at the time it was released
becomes the constant driving speed.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст