Mitsubishi L200. Manual — part 473
ON-VEHICLE SERVICE
PARKING BRAKES
36-5
(2) Turn the ignition switch to "ON" position, and
start the engine.
(3) Repeatedly depress the brake pedal until the
pedal stroke no longer changes with the
engine running.
NOTE: Depressing the brake pedal repeatedly
adjusts shoe clearance correctly.
(4) Turn the ignition switch to "OFF" position, and
stop the engine.
CAUTION
If the parking brake pull rod stroke is below the
standard value and the braking is too firm, the
rear brakes may drag.
(5) Adjust with the adjusting nut so that the joint
and the equalizer are vertical as shown in the
figure.
(6) After adjusting the parking brake pull rod
stroke, jack up the rear end of the vehicle, and
then release the parking brake and turn the
rear wheels to check that the rear brakes are
not dragging.
PARKING BRAKE SWITCH CHECK
<VEHICLES WITH FRONT SEPARATE
SEAT>
M1361003300745
CAUTION
Do not apply grease or lubricant to the switch
and the switch installation section to avoid mal-
function of the switch. In addition, do not use
gloves which have grease on them.
1. Remove the rear floor console assembly (Refer to
GROUP 52A
− Rear Floor Console Assembly ).
AC502267AB
2. Check for continuity between the parking brake
switch terminal and the switch mounting bolt.
Check condition
Normal condition
When parking brake lever is
pulled.
Continuity exists
(2
Ω or less)
When parking brake lever is
released.
Open circuit
PARKING BRAKE SWITCH CHECK
<VEHICLES WITH FRONT BENCH SEAT>
M1361003300734
CAUTION
Do not apply grease or lubricant to the switch
and the switch installation section to avoid mal-
function of the switch. In addition, do not use
gloves which have grease on them.
1. Remove the lower panel assembly (Refer to
GROUP 52A
− Instrument Panel Assembly ).
AC505761AB
2. Check for continuity between the parking brake
switch terminal and the switch mounting nut.
Check condition
Normal condition
When parking brake pull rod
is pulled.
Continuity exists
(2
Ω or less)
When parking brake pull rod
is released.
Open circuit
PARKING BRAKE LEVER <Vehicles with front separate seat>
PARKING BRAKES
36-6
PARKING BRAKE LEVER <Vehicles with front separate
seat>
REMOVAL AND INSTALLATION
M1361001300556
CAUTION
Do not apply grease or lubricant to the switch and the switch installation section to avoid malfunction
of the switch. In addition, do not use gloves which have grease on them.
Pre-removal Operation
Rear floor console assembly removal (Refer to GROUP 52A
− Rear Floor Console Assembly ).
Post-installation Operation
• Parking brake lever stroke adjustment (Refer to
).
• Rear floor console assembly installation (Refer to
GROUP 52A
− Rear Floor Console Assembly ).
AC805172 AB
A
Section A - A
Upper view
1
2
3
4
5
6
1.4 ± 0.2 N·m
A
Removal steps
1.
Adjuster
2.
Adjuster holder
3.
Parking brake switch connector
connection
4.
Parking brake lever assembly
(including parking brake switch)
5.
Parking brake switch
6.
Parking brake lever assembly
Removal steps (Continued)
PARKING BRAKE PULL ROD AND PARKING BRAKE FRONT CABLE <Vehicles with front bench seat>
PARKING BRAKES
36-7
PARKING BRAKE PULL ROD AND PARKING BRAKE
FRONT CABLE <Vehicles with front bench seat>
REMOVAL AND INSTALLATION
M1361002800060
CAUTION
Do not apply grease or lubricant to the switch and the switch installation section to avoid malfunction
of the switch. In addition, do not use gloves which have grease on them.
Pre-removal Operation
Lower panel assembly removal (Refer to GROUP 52A
−
Instrument Panel Assembly ).
Post-installation Operation
• Parking brake pull rod stroke adjustment (Refer to
).
• Lower panel assembly installation (Refer to GROUP 52A
− Instrument Panel Assembly ).
AC510141
2
3
2
1
4
5
6
9
10
7
8
<LHD>
<RHD>
AC
3
1
4
5
6
9
10
7
8
:Ratchet of parking brake pull rod and rod groove
Removal steps
1.
Parking brake switch
2.
Return spring
3.
Parking brake front cable
connection (lever side)
4.
Clip
5.
Clip
6.
Pin
7.
Pin
8.
Parking brake front cable
connection (parking brake pull rod
side)
<<
A
>>
9.
Parking brake front cable
assembly
10. Parking brake pull rod assembly
PARKING BRAKE CABLE <Vehicles with front separate seat>
PARKING BRAKES
36-8
REMOVAL SERVICE POINT
<<A>> PARKING BRAKE FRONT CABLE AND
PARKING BRAKE PULL ROD ASSEMBLY CON-
NECTION
AC506381AB
Pin
Groove
Parking brake pull rod assembly
Pull the parking brake pull rod to the position shown
in the figure. Then, fit the pin to the groove and
remove the parking brake front cable.
PARKING BRAKE CABLE <Vehicles with front separate
seat>
REMOVAL AND INSTALLATION
M1361001900989
Post-installation Operation
Parking brake lever stroke adjustment (Refer to
AC508552AC
3
1
2
4
5
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст