Mitsubishi L200. Manual — part 649
AC805944
9.0 ± 2.0 N·m
2
3
<Vehicles with side-airbag and curtain air bag>
5.0 ± 1.0 N·m
1
5.0 ± 1.0 N·m
4
AB
Removal steps
•
Rear floor console (Refer to
GROUP 52A, Rear floor console
assembly ).
•
Front floor console (Refer to
GROUP 52A, Font floor console
assembly ).
1.
SRS-ECU mounting bolt
2.
SRS-ECU mounting bolt (earth
bolt)
3.
Flange nut
4.
SRS-ECU
Installation steps
>>
A
<<
4.
SRS-ECU
3.
Flange nut
>>
B
<<
2.
SRS-ECU mounting bolt (earth
bolt)
1.
SRS-ECU mounting bolt
•
Front floor console (Refer to
GROUP 52A, Font floor console
assembly ).
•
Rear floor console (Refer to
GROUP 52A, Rear floor console
assembly ).
•
Negative battery cable connection
>>
C
<<
•
Post-installation inspection
SRS CONTROL UNIT (SRS-ECU)
SUPPLEMENTAL RESTRAINT SYSTEM (SRS)
52B-267
INSTALLATION SERVICE POINTS
>>A<< SRS-ECU INSTALLATION
WARNING
The SRS may not activate if SRS-ECU is not
installed properly.
>>B<< SRS-ECU MOUNTING BOLT (EARTH
BOLT) INSTALLATION
AC701047
Earth bolt head mark
AB
Check the head mark "E" and install the earth bolt.
>>C<< POST-INSTALLATION INSPECTION
1. Connect the negative battery cable.
2. Turn the ignition switch to "ON" position.
AC900540 AB
SRS warning lamp
3. Does the "SRS" warning lamp illuminate for
approximately seven seconds, and go out?
4. If no, refer to troubleshooting (Refer to
DRIVER'S AND PASSENGER'S (FRONT) AIR BAG MODULE(S) AND CLOCK SPRING
SUPPLEMENTAL RESTRAINT SYSTEM (SRS)
52B-268
INSPECTION
M1524002200540
WARNING
If any problems are found, replace the SRS-
ECU.
• Check the SRS-ECU and brackets for dents,
cracks or deformation.
• Check the SRS-ECU connector for damage, and
the terminals for deformation.
NOTE: For the checks other than the items above,
refer to "Troubleshooting" (Refer to
).
DRIVER'S AND PASSENGER'S (FRONT) AIR BAG
MODULE(S) AND CLOCK SPRING
REMOVAL AND INSTALLATION
M1524014501132
WARNING
•
Disconnect the negative battery terminal and wait for 60 seconds or more before starting
work. Furthermore, the disconnected battery terminal should be covered with tape to
insulate it.
•
Never attempt to disassemble or repair the air bag modules or clock spring. If faulty,
replace it.
•
Do not drop the air bag modules or clock spring or allow contact with water, grease or oil.
Replace it if a dent, crack, deformation or rust is detected.
•
The removed air bag module should be stored in a clean, dry place with the deployment
surface facing up. Do not place anything on top of it.
•
Do not expose the air bag modules to temperatures over 93
°
C.
•
After deployment of an air bag, the driver’s and passenger’s (front) air bag module has
been replaced with a new one. Also, check the clock spring, and replace with a new one if
there is an abnormality.
•
Wear gloves and safety glasses when handling air bags that have already deployed.
•
An undeployed air bag module should only be disposed of in accordance with the proce-
dures (Refer to
).
DRIVER'S AND PASSENGER'S (FRONT) AIR BAG MODULE(S) AND CLOCK SPRING
SUPPLEMENTAL RESTRAINT SYSTEM (SRS)
52B-269
<DRIVER’S AIR BAG MODULE AND CLOCK SPRING>
Pre-removal Operation
• Disconnect the Negative Battery Terminal.
AC501231
AC809519
1
4
5
6
4
5
9.0 ± 2.0 N·m
A
B
B
Column switch
Section A - A
Section B - B
Claw
Claw
6
A
3
2
5
4
Note
: Claw position
<Vehicles without wide fender (optional)>
<Vehicles with fender (optional)>
1
AC
41 ± 8 N·m
41 ± 8 N·m
Air bag module removal steps
<<
A
>>
1. Cover
2. Horn connector connection
<<
B
>>
3. Driver’s air bag module connector
connection
<<
C
>>
4. Driver’s air bag module
Air bag module removal steps
Clock spring removal steps
<<
A
>>
1. Cover
2. Horn connector connection
<<
B
>>
3. Driver’s air bag module connector
connection
<<
C
>>
4. Driver’s air bag module
<<
D
>>
5. Steering wheel
•
Column cover (Refer to GROUP 37,
Steering shaft ).
<<
E
6. Clock spring
Air bag module installation steps
>>
A
<< • Pre-installation inspection
>>
C
<< 4. Driver’s air bag module
3. Driver’s air bag module connector
connection
2. Horn connector connection
1. Cover
•
Negative battery cable connection
>>
D
<< • Post-installation inspection
Clock spring installation steps
>>
A
<< • Pre-installation inspection
>>
B
<< 6. Clock spring
•
Column cover (Refer to GROUP 37,
Steering shaft ).
>>
C
<< 5. Steering wheel
>>
C
<< 4. Driver’s air bag module
3. Driver’s air bag module connector
connection
2. Horn connector connection
1. Cover
•
Negative battery cable connection
>>
D
<< • Post-installation inspection
DRIVER'S AND PASSENGER'S (FRONT) AIR BAG MODULE(S) AND CLOCK SPRING
SUPPLEMENTAL RESTRAINT SYSTEM (SRS)
52B-270
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст