Mitsubishi L200. Manual — part 555
WINDSHIELD WIPER AND WASHER
EXTERIOR
51-36
Inspection Procedure 1: The windshield wipers do not work at all.
CAUTION
Whenever the ECU is replaced, ensure that the input and output signal circuits are normal.
AC903741
Windshield Wiper Power Supply Circuit
IGNITION
SWITCH (ACC)
WIPER SPEED
SWITCHING
RELAY
WINDSHIELD
WIPER
MOTOR
CIRCUIT
BREAKER
ETACS-ECU
J/B SIDE
AB
COLUMN
SWITCH
COLUMN-ECU
Wire colour code
B : Black LG : Light green G : Green L : Blue W : White Y : Yellow SB : Sky blue
BR : Brown O : Orange GR : Grey R : Red P : Pink V : Violet PU : Purple SI : Silver
COMMENTS ON TROUBLE SYMPTOM
The windshield wiper motor, the column switch or the
ETACS-ECU may be defective.
PROBABLE CAUSES
• Malfunction of the windshield wiper motor
• Malfunction of the column switch
• Malfunction of the ETACS-ECU
• Damaged harness wires and connectors
DIAGNOSIS PROCEDURE
STEP 1. M.U.T.-III diagnosis code.
When the ignition switch is turned to the "LOCK"
(OFF) position, check that the ETACS-ECU does not
set the diagnosis code.
Q: Is the diagnosis code set?
YES :
Refer to GROUP 54A, ETACS Diagnosis
Code Chart .
NO :
Go to Step 2.
WINDSHIELD WIPER AND WASHER
EXTERIOR
51-37
STEP 2. Check the power supply circuit.
When the ignition switch is turned to the LOCK
(OFF) position, check if the hazard warning lamps
illuminate.
Q: Is the check result normal?
YES :
Go to Step 3.
NO :
Refer to GROUP 54A,ETACS Inspection
Procedure A-1 "Check The Battery Power
Supply Circuit to The ETACS-ECU ."
STEP 3. M.U.T.-III data list
Check the input signals below which are related to
the windshield wiper.
•
Item
No.
Item name
Normal condition
29
Ignition switch(ACC) ON
Turn the ignition switch to the "ACC" position.
OK: Normal condition is displayed.
Q: Is the check result normal?
YES :
Go to Step 4.
NO :
Refer to GROUP 54A, ETACS Inspection
Procedure C-2 "The Ignition Switch (ACC)
signal is not received ."
STEP 4. Connector check: A-05 windshield wiper
motor connector
AC903897
AJ
Connector: A-05 <LHD>
Harness side
A-05 (GR)
AC903889
AC
Connector: A-05 <RHD>
Harness side
A-05 (GR)
Q: Is the check result normal?
YES :
Go to Step 5.
NO :
Repair the connector.
STEP 5. Check the windshield wiper motor
assembly.
Refer to
Q: Is the check result normal?
YES :
Go to Step 6.
NO :
Replace the windshield wiper motor
assembly.
STEP 6. Resistance measurement at the A-05
windshield wiper motor connector.
AC903897
AJ
Connector: A-05 <LHD>
Harness side
A-05 (GR)
AC903889
AC
Connector: A-05 <RHD>
Harness side
A-05 (GR)
(1) Disconnect the connector, and measure at the
wiring harness side.
AC310506
Connector A-05
FX
(Harness side)
(2) Continuity between A-05 windshield wiper motor
connector terminal No.2 and body earth
OK: Continuity exists (2
Ω or less)
Q: Is the check result normal?
YES :
Go to Step 8.
NO :
Go to Step 7.
WINDSHIELD WIPER AND WASHER
EXTERIOR
51-38
STEP 7. Check the wiring harness between A-05
windshield wiper motor connector terminal No.2
and body earth.
AC903897
AJ
Connector: A-05 <LHD>
Harness side
A-05 (GR)
AC903889
AC
Connector: A-05 <RHD>
Harness side
A-05 (GR)
• Check the earth wires for open circuit.
Q: Is the check result normal?
YES :
The trouble can be an intermittent
malfunction (Refer to GROUP 00, How to
use Troubleshooting/inspection Service
Points
− How to Cope with Intermittent
Malfunction ).
NO :
Repair the wiring harness and go to Step 8.
STEP 8. Connector check: C-218 ETACS-ECU
connector
AC509934
Connector: C-218 <LHD>
AJ
Junction
block
Junction block side
AC509943
Connector: C-218 <RHD>
AC
Junction block
(Rear view)
Junction block side
Q: Is the check result normal?
YES :
Go to Step 9.
NO :
Repair the defective connector.
WINDSHIELD WIPER AND WASHER
EXTERIOR
51-39
STEP 9. Check the wiring harness between C-218
ETACS-ECU connector terminal Nos. 8,7 and A-
05 windshield wiper motor connector terminal
Nos. 3,5 <LHD> or 1,4 <RHD>.
AC509934
Connector: C-218 <LHD>
AJ
Junction
block
Junction block side
AC509943
Connector: C-218 <RHD>
AC
Junction block
(Rear view)
Junction block side
AC903897
AJ
Connector: A-05 <LHD>
Harness side
A-05 (GR)
AC903889
AC
Connector: A-05 <RHD>
Harness side
A-05 (GR)
NOTE:
AC509934
Connector: C-210 <LHD>
Junction block
AN
Harness side
AC509936
Connector: C-210 <RHD>
Harness side
AJ
Junction block
(Front view)
Prior to the wiring harness inspection, check the
junction block connector C-210 and repair if neces-
sary.
• Check the output lines for open circuit.
Q: Is the check result normal?
YES :
Go to Step 10.
NO :
Repair the wiring harness.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст