Mitsubishi L200. Manual — part 554
UNDER COVER
EXTERIOR
51-32
UNDER COVER
REMOVAL AND INSTALLATION
M1511019601231
ACB00494AB
1
2
<2WD>
< High rider and 4WD>
1
Removal steps
1.
Under skid plate
2.
Engine room under cover front
WINDSHIELD WIPER AND WASHER
SERVICE SPECIFICATION
M1511000300778
Item
Standard value (reference)
Stop position of the windshield wiper arm/blade assembly (Distance between
the edge of the wiper blade and the end of the deck garnish) mm
Driver’s side: (31
± 5)
Passenger’s side: (33
± 5)
LUBRICANT
M1511000400043
Item
Specified lubricant
Quantity
Wiper motor link rod
Contact joint between
link rod and wiper motor
link plate
Multipurpose grease SAE J310,
NLGI No.2 or equivalent
As required
WINDSHIELD WIPER AND WASHER
EXTERIOR
51-33
SPECIAL TOOLS
M1511000602764
Tool
Number
Name
Use
MB992326
MB992326
Adjustment tool,
washer nozzle
Injection angle adjustment of the
washer nozzle
WINDSHIELD WIPER AND WASHER
EXTERIOR
51-34
Tool
Number
Name
Use
MB991910
MB991826
MB991955
MB991911
MB991824
MB991827
MB991825
a
b
c
d
e
f
DO NOT USE
MB991955
a: MB991824
b: MB991827
c: MB991910
d: MB991911
e: MB991825
f: MB991826
M.U.T.-III sub-
assembly
a: Vehicle
Communication
Interface (V.C.I.)
b: M.U.T.-III USB
cable
c: M.U.T.-III main
harness A
(Vehicles with CAN
communication
system)
d: M.U.T.-III main
harness B
(Vehicles without
CAN
communication
system)
e: M.U.T.-III measure
adapter
f: M.U.T.-III trigger
harness
CAUTION
For vehicles with CAN
communication, use M.U.T.-III
main harness A to send
simulated vehicle speed. If you
connect M.U.T.-III main harness
B instead, the CAN
communication does not
function correctly.
Checking windshield wiper
intermittent time
Lighting control sensor (rain
sensor) adaptation
MB991223
a
d
c
b
DO NOT USE
BF
MB991223
a: MB991219
b: MB991220
c: MB991221
d: MB991222
Harness set
a: Check harness
b: LED harness
c: LED harness
adapter
d: Probe
Continuity check and voltage
measurement at harness wire or
connector
a: For checking connector pin
contact pressure
b: For checking power supply
circuit
c: For checking power supply
circuit
d: For connecting a locally
sourced tester
MB992006
WINDSHIELD WIPER AND WASHER
EXTERIOR
51-35
TROUBLESHOOTING
DIAGNOSIS TROUBLESHOOTING FLOW
M1511014600404
Refer to GROUP 00, How to Use Troubleshooting/
Inspection Service Points
− Contents of Trouble-
shooting .
TROUBLE SYMPTOM CHART
M1511015001851
Symptom
Inspection
procedure
Reference
page
The windshield wipers do not work at all.
1
The windshield wipers do not work normally.
2
The windshield wipers do not stop at the specified park position.
3
The intermittent wiper interval cannot be adjusted by operating the windshield
intermittent wiper volume control.
4
The intermittent wiper interval is not changed according to the vehicle speed.
5
The rain sensitive AUTO wiper function does not work at all <Vehicles with
lighting control sensor>.
6
The rain sensitive AUTO wiper function works even though there is no rainfall
<Vehicles with lighting control sensor>..
7
Sometimes the rain sensitive wiper function works even though there is no
rainfall <Vehicles with lighting control sensor>.
8
The windshield washer does not work normally.
9
NOTE: Even when the ETACS-ECU has failed, the
windshield wiper can work at low speed as fail-safe
mode.
MB992006
Extra fine probe
Continuity check and voltage
measurement at harness wire or
connector
Tool
Number
Name
Use
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст