Mitsubishi L200. Manual — part 681
COMBINATION METER
CHASSIS ELECTRICAL
54A-91
INSPECTION
INSPECTION
M1540207600116
CHECK OF COMBINATION METER
INTERNAL RESISTANCE
Measure the resistance between terminals using an ohmmeter.
AC502672AF
C-111
C-112
C-113
Terminal No. to measure
resistance
Terminal name
Standard value
42
− 13
Battery power source and earth
1 M
Ω or more
42
− 57
Battery power source and earth
1 M
Ω or more
36
− 13
IG power source and earth
1 M
Ω or more
36
− 57
IG power source and earth
1 M
Ω or more
42
− 22
Battery power source and fuel gauge
1 M
Ω or more
36
− 22
IG power source and fuel gauge
1 M
Ω or more
22
− 13
Fuel gauge and earth
−
22
− 57
Fuel gauge and earth
−
42
− 21
Battery power source and engine coolant temperature
gauge
1 M
Ω or more
36
− 21
IG power source and engine coolant temperature gauge 1 M
Ω or more
21
− 13
Engine coolant temperature gauge and earth
−
21
− 57
Engine coolant temperature gauge and earth
−
HEADLAMP
CHASSIS ELECTRICAL
54A-92
HEADLAMP
SERVICE SPECIFICATIONS
M1540100200411
PRECAUTIONS ON HOW TO USE THE HEADLAMP ASSEMBLY
Be careful with the following items as resin lenses
are used in the headlamp assembly.
• Don't illuminate the headlamp for three minutes
or more when the headlamp is covered with
scratch protector.
• Don't tape the outer lens.
• Don't scratch the outer lens surface with a sharp
edged special tool.
• Use the specified genuine bulb.
Item
Standard value
Limit
Headlamp aiming
Low beam
(halogen
headlamp)
Vertical
direction
36 mm (0.69
°)
below horizontal
line (H)
Between 21 mm
(0.4
°) to 51 mm
(0.98
°) downward
from the horizontal
line (H)
Horizontal
direction
Elbow point
intersects the
vertical line (V)
± 26 mm (± 0.5°)
from the vertical
line (V)
Headlamp luminous intensity measurement cd
(When a screen is set 25 m ahead of the vehicle)
−
30,000 cd or more
HEADLAMP
CHASSIS ELECTRICAL
54A-93
SPECIAL TOOLS
M1540104400031
HEADLAMP
CHASSIS ELECTRICAL
54A-94
Tool
Number
Name
Use
MB991955
a. MB991824
b. MB991827
c. MB991910
d. MB991911
e. MB991825
f. MB991826
M.U.T.-III sub-
assembly
a. Vehicle
Communicati
on Interface
(V.C.I.)
b. M.U.T.-III
USB cable
c. M.U.T.-III
main harness
A (Vehicles
with CAN
communicatio
n system)
d. M.U.T.-III
main harness
B (Vehicles
without CAN
communicatio
n system)
e. M.U.T.-III
measure
adapter
f. M.U.T.-III
trigger
harness
CAUTION
For vehicles with CAN
communication, use M.U.T.-III
main harness A to send
simulated vehicle speed. If you
connect M.U.T.-III main harness B
instead, the CAN communication
does not function correctly.
Diagnosis code, service data and
actuator test check.
MB991223
a. MB991219
b. MB991220
c. MB991221
d. MB991222
Harness set
a. Check
harness
b. LED harness
c. LED harness
adapter
d. Probe
Continuity check and voltage
measurement at harness wire or
connector
a. For checking connector pin
contact pressure
b. For checking power supply
circuit
c. For checking power supply
circuit
d. For connecting a locally sourced
tester
MB991910
MB991826
MB991955
MB991911
MB991824
MB991827
MB991825
a
b
c
d
e
f
DO NOT USE
MB991223
a
d
c
b
DO NOT USE
BA
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст