Mitsubishi L200. Manual — part 709
REAR COMBINATION LAMP
CHASSIS ELECTRICAL
54A-203
STEP 6. Check the wiring harness from F-04
<vehicles with rear body> or F-23 <vehicles
without rear body> rear combination lamp (tail:
LH) connector or F-02 <vehicles with rear body>
or F-19 <vehicles without rear body> rear
combination lamp (tail: RH) connector terminal
No.3 to C-218 ETACS-ECU connector terminal
No.15.
NOTE:
Prior to the wiring harness inspection, check junction
block connector C-221 <LHD> or C-204 <RHD> and
intermediate connector F-07 and C-31 <RHD>, and
repair if necessary.
• Check the output lines for open circuit.
Q: Is the check result normal?
YES :
Go to Step 7.
NO :
Repair the wiring harness.
STEP 7. Retest the system.
Check that the tail/stop lamps illuminate normally.
Q: Is the check result normal?
YES :
The trouble can be an intermittent
malfunction (Refer to GROUP 00
− How to
use Troubleshooting/inspection Service
Points
− How to Cope with Intermittent
Malfunction ).
NO :
Replace the tail lamp socket.
AC509935AE
Connectors: C-218, C-221 <LHD>
C-218
C-221
Junction block side
C-218
C-221
Harness side
AC509934
Connector: C-218 <LHD>
AJ
Junction
block
Junction block side
AC903957AD
Harness side
F-02 (B)
Connectors: F-02, F-04, F-07, F-19, F-23
<Vehicles without
rear body>
F-19
F-23
F-02, F-04
F-04 (B)
Harness side
F-19, F-23
F-07 (B)
F-07
AC903865
Connector: C-31 <RHD>
AS
AC509936
Connector: C-204 <RHD>
Harness side
AO
Junction block
(Front view)
REAR COMBINATION LAMP
CHASSIS ELECTRICAL
54A-204
REMOVAL AND INSTALLATION
M1541402200400
<VEHICLES WITH REAR BODY>
AC502678AB
3
4
5
2
6
2
1.5 ± 0.2 N·m
Section A - A
Section B - B
A
A
B
B
C
C
Section C - C
2
2
9
8
7
1
Removal steps
1.
Rear combination lamp assembly
2.
Rear combination lamp unit
3.
Socket
4.
Turn-signal lamp bulb
5.
Tail lamp and stop lamp bulb
6.
Back-up lamp bulb
7.
Grommet
8.
Grommet
9.
Grommet
Removal steps (Continued)
REAR COMBINATION LAMP
CHASSIS ELECTRICAL
54A-205
<VEHICLES WITHOUT REAR BODY>
AC903483AB
2
4
3
5
6
7
1
9
8
4.9 ± 0.7 N·m
11.3 ± 2.4 N·m
9
11.3 ± 2.4 N·m
4.9 ± 0.7 N·m
Removal steps
1.
Rear combination lamp assembly
2.
Rear combination lamp lens
3.
Rear combination lamp gasket
4.
Back-up lamp bulb
5.
Tail lamp and stop lamp bulb
6.
Turn-signal lamp bulb
7.
Rear combination lamp body
8.
Licence plate lamp bracket
assembly
9.
Rear combination lamp bracket
assembly
Removal steps (Continued)
REFLECTOR
CHASSIS ELECTRICAL
54A-206
REFLECTOR
SPECIAL TOOL
M1542500200017
REMOVAL AND INSTALLATION
M1542500300014
Tool
Number
Name
Use
MB990784
Ornament
remover
Removal of reflector
MB990784
AC502719AB
4.9 ± 0.7 N·m
Section A - A
Section B - B
A
A
1
B
B
2
3
1
1
Removal steps
1.
Reflector
2.
Grommet
3.
Grommet
Removal steps (Continued)
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст