Mitsubishi L200. Manual — part 708
REAR COMBINATION LAMP
CHASSIS ELECTRICAL
54A-199
NOTE: Prior to the wiring harness inspection, check
the junction block connector C-211, and repair if nec-
essary.
• Check the power supply line from the fusible link
(23) for open circuit and short.
Q: Is the check result normal?
YES :
The trouble can be an intermittent
malfunction (Refer to GROUP 00
− How to
use Troubleshooting/inspection Service
Points
− How to Cope with Intermittent
Malfunction ).
NO :
Repair the wiring harness.
STEP 6. Retest the system.
Check that the tail lamps illuminate normally.
Q: Is the check result normal?
YES :
The trouble can be an intermittent
malfunction (Refer to GROUP 00
− How to
use Troubleshooting/inspection Service
Points
− How to Cope with Intermittent
Malfunction ).
NO :
Replace the ETACS-ECU and register the
ID codes (Refer to
AC503086
AE
Battery
Front of vehicle
24
23
22
21
20
19
Fusible link (23)
AC509935
Connectors: C-211, C-218 <LHD>
AB
Junction block
Junction block side
C-218
Harness side
C-211
C-218
C-211
AC509936
Connector: C-211 <RHD>
Harness side
BE
Junction block
(Front view)
AC509943
Connector: C-218 <RHD>
AC
Junction block
(Rear view)
Junction block side
REAR COMBINATION LAMP
CHASSIS ELECTRICAL
54A-200
Inspection Procedure 2: One of tail lamps does not illuminate.
CAUTION
Whenever the ECU is replaced, ensure that the input and output signal circuits are normal.
COMMENTS ON TROUBLE SYMPTOM
If one of the tail lamps does not illuminate, the wiring
harness connector(s), the bulb or the fuse may be
defective or burned out.
PROBABLE CAUSES
• Burned-out bulb
• Damaged harness wires and connectors
NOTE
: VEHICLES WITH REAR BODY
: VEHICLES WITHOUT REAR BODY
: LHD
: RHD
Wire colour code
B : Black LG : Light green G : Green L : Blue W : White Y : Yellow SB : Sky blue
BR : Brown O : Orange GR : Grey R : Red P : Pink V : Violet PU : Purple SI : Silver
Tail Lamps Circuit
ETACS-ECU
TAIL LAMP RELAY
J/B SIDE
REAR COMBINATION
LAMP
(TAIL:RH)
(TAIL:LH)
REAR COMBINATION LAMP
CHASSIS ELECTRICAL
54A-201
DIAGNOSIS PROCEDURE
STEP 1. Connector check: F-04 <vehicles with
rear body> or F-23 <vehicles without rear body>
rear combination lamp (tail: LH) connector or F-
02 <vehicles with rear body> or F-19 <vehicles
without rear body> rear combination lamp (tail:
RH) connector
Q: Is the check result normal?
YES :
Go to Step 2.
NO :
Repair the defective connector.
STEP 2. Check the bulbs of the tail lamps.
Check the bulb of the lamp which does not illumi-
nate.
Q: Is the check result normal?
YES :
Go to Step 3.
NO :
Replace the bulb of the lamp which does not
illuminate.
STEP 3. Resistance measurement at the F-04
<vehicles with rear body> or F-23 <vehicles
without rear body> rear combination lamp (tail:
LH) connector or F-02 <vehicles with rear body>
or F-19 <vehicles without rear body> rear
combination lamp (tail: RH) connector.
(1) Disconnect the connector, and measure at the
wiring harness side.
(2) Check the resistance between the lamp
connector and body earth.
•
Resistance between F-04 rear combination lamp
(tail: LH) or F-02 rear combination lamp (tail:
RH) connector terminal No.5 and body earth
<vehicles with rear body>
•
Resistance between F-23 rear combination lamp
(tail: LH) or F-19 rear combination lamp (tail:
RH) connector terminal No.5 and body earth
<vehicles without rear body>
OK: Continuity exists (2
Ω or less)
Q: Is the check result normal?
YES :
Go to Step 5.
NO :
Go to Step 4.
AC903957AC
Harness side
F-02 (B)
Connectors: F-02, F-04, F-19, F-23
<Vehicles without
rear body>
F-19
F-23
F-02, F-04
F-04 (B)
Harness side
F-19, F-23
AC903957AC
Harness side
F-02 (B)
Connectors: F-02, F-04, F-19, F-23
<Vehicles without
rear body>
F-19
F-23
F-02, F-04
F-04 (B)
Harness side
F-19, F-23
AC310506
Connectors F-02 , F-04
(Harness side)
FV
AC310506
Connectors F-19, F-23
(Harness side)
JN
REAR COMBINATION LAMP
CHASSIS ELECTRICAL
54A-202
STEP 4. Check the wiring harness from F-04
<vehicles with rear body> or F-23 <vehicles
without rear body> rear combination lamp (tail:
LH) connector or F-02 <vehicles with rear body>
or F-19 <vehicles without rear body> rear
combination lamp (tail: RH) connector terminal
No.5 to body earth.
NOTE: Prior to the wiring harness inspection, check
intermediate connector F-07, and repair if necessary.
• Check the earth wires for open circuit.
Q: Is the check result normal?
YES :
Go to Step 5.
NO :
Repair the wiring harness.
STEP 5. Connector check: C-218 ETACS-ECU
connector
Q: Is the check result normal?
YES :
Go to Step 6.
NO :
Repair the defective connector.
AC903957AD
Harness side
F-02 (B)
Connectors: F-02, F-04, F-07, F-19, F-23
<Vehicles without
rear body>
F-19
F-23
F-02, F-04
F-04 (B)
Harness side
F-19, F-23
F-07 (B)
F-07
AC509934
Connector: C-218 <LHD>
AJ
Junction
block
Junction block side
AC509943
Connector: C-218 <RHD>
AC
Junction block
(Rear view)
Junction block side
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст