Mitsubishi L200. Manual — part 791
ETACS
CHASSIS ELECTRICAL
54A-531
STEP 3. Check the wiring harness between C-219
ETACS-ECU connector terminal No.74 and the
ignition switch (ACC).
NOTE:
Prior to the wiring harness inspection, check joint
connector C-127, junction block connectors C-207
and C-208, and repair if necessary.
• Check the power supply line for open circuit and
short circuit.
Q: Is the check result normal?
YES :
Refer to Inspection Procedure 2
"Malfunction of the ignition switch power
supply system."
NO :
Repair the wiring harness.
STEP 4. M.U.T.-III data list
Check the input signals from the ignition switch
(ACC).
• Turn the ignition switch to the "ACC" position.
OK: Normal condition is displayed.
Q: Is the check result normal?
AC509935AG
Connectors: C-207, C-208, C-219 <LHD>
C-219 (GR)
C-207
Harness side
C-219
C-208
C-208
C-207
Harness side
Harness side
AC509943
Connector: C-219 <RHD>
AB
C-219 (GR)
Harness side
Junction block
(Rear view)
Item
No.
Item name
Normal condition
29
Ignition switch(ACC) ON
AC903853
Connector: C-127 <LHD>
AE
C-127 (GR)
AC903865
Connector: C-127 <RHD>
AD
C-127 (GR)
AC509936
Connectors: C-207, C-208 <RHD>
C-207
C-208
C-207
Harness side
Harness side
C-208
AB
Junction block
(Front view)
ETACS
CHASSIS ELECTRICAL
54A-532
YES :
The trouble can be an intermittent
malfunction (Refer to GROUP 00
− How to
use Troubleshooting/inspection Service
Points
− How to Cope with Intermittent
Malfunction ).
NO :
Replace the ETACS-ECU and register the
ID codes (Refer to
Inspection Procedure C-3: The ignition switch (IG1) signal is not received.
CAUTION
Whenever the ECU is replaced, ensure that the input signal circuit is normal.
COMMENTS ON TROUBLE SYMPTOM
Input signal from the ignition switch (IG1) is used to
operate the functions below. If the signal is abnormal,
these functions will not work normally.
• Lamp reminder function
• Turn-signal lamp
PROBABLE CAUSES
• Malfunction of the ETACS-ECU
• Damaged harness wires and connectors
Ignition Switch (IG1) Input Circuit
ETACS-ECU
IGNITION
SWITCH (IG1)
Wire colour code
B : Black LG : Light green G : Green L : Blue W : White Y : Yellow SB : Sky blue
BR : Brown O : Orange GR : Grey R : Red P : Pink V : Violet PU : Purple SI : Silver
ETACS
CHASSIS ELECTRICAL
54A-533
DIAGNOSIS PROCEDURE
STEP 1. Connector check: C-219 ETACS-ECU
connector
Q: Is the check result normal?
YES :
Go to Step 2.
NO :
Repair the defective connector.
STEP 2. Voltage measurement at the C-219
ETACS-ECU connector.
(1) Disconnect the connector, and measure at the
wiring harness side.
(2) Turn the ignition switch to the "ON" position.
(3) Voltage between C-219 ETACS-ECU connector
terminal No.68 and body earth
OK: System voltage
Q: Is the check result normal?
YES :
Go to Step 4.
NO :
Go to Step 3.
AC509934
Connector: C-219 <LHD>
AD
C-219 (GR)
Harness side
Junction block
AC509943
Connector: C-219 <RHD>
AB
C-219 (GR)
Harness side
Junction block
(Rear view)
AC509934
Connector: C-219 <LHD>
AD
C-219 (GR)
Harness side
Junction block
AC509943
Connector: C-219 <RHD>
AB
C-219 (GR)
Harness side
Junction block
(Rear view)
AC310507
(Harness side)
Connector: C-219
JI
ETACS
CHASSIS ELECTRICAL
54A-534
STEP 3. Check the wiring harness between C-219
ETACS-ECU connector terminal No.68 and the
ignition switch (IG1).
NOTE:
Prior to the wiring harness inspection, check joint
connector C-132, junction block connectors C-207
and C-209, and repair if necessary.
• Check the power supply line for open circuit and
short circuit.
Q: Is the check result normal?
YES :
Refer to Inspection Procedure 2
"Malfunction of the ignition switch power
supply system."
NO :
Repair the wiring harness.
STEP 4. M.U.T.-III data list
Check the input signal from the ignition switch (IG1).
• Turn the ignition switch to the "ON" position.
OK: Normal condition is displayed.
Q: Is the check result normal?
AC509935AH
Connectors: C-207, C-209, C-219 <LHD>
C-219 (GR)
C-207
Harness side
C-219
C-209
C-209
C-207
Harness side
Harness side
AC509943
Connector: C-219 <RHD>
AB
C-219 (GR)
Harness side
Junction block
(Rear view)
Item
No.
Item name
Normal condition
30
Ignition switch(IG1)
ON
AC903853
Connector: C-132 <LHD>
AC
C-132 (GR)
AC903865
Connector: C-132 <RHD>
AB
C-132 (GR)
AC509936 AN
Connectors: C-207, C-209 <RHD>
Harness side
C-209
C-207
Harness side
C-209
C-207
Junction block (Front view)
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст