Mitsubishi Lancer Evolution 7. Manual — part 285
REAR AXLE -
Rear Hub Assembly
27B-25
REAR HUB ASSEMBLY
REMOVAL AND INSTALLATION
Caution
If the vehicle is equipped with the Brembo disc brake, during maintenance, take care not to contact
the parts or tools to the caliper because the paint of caliper will be scratched. And if there is
brake fluid on the caliper, wipe out quickly.
Pre-removal Operation
Gear Oil Draining (Refer to P. 27B-17.)
Post-installation Operation
D
Gear Oil Filling (Refer to P. 27B-17.)
D
Parking Brake Lever Stroke Adjustment (Refer to
GROUP 36 – On-vehicle Service.)
2
118 ± 19 N·m
4
1
3
225 ± 25 N·m
8
7
6
5
10
9
54 ± 5 N·m
81 ± 6 N·m
Removal steps
A
A"
1. Rear brake caliper
2. Rear brake disc
3. Parking brake shoe & lining assembly
(Refer to GROUP 36 - Parking Brake
Drum.)
4. Clip
5. Parking brake cable connection
6. Split pin
A
B" "AA 7. Drive shaft nut
8. Rear drive shaft assembly
A
C"
9. Rear hub assembly
10. Backing plate
REAR AXLE -
Rear Hub Assembly
27B-26
REMOVAL SERVICE POINTS
A
A" REAR BRAKE CALIPER REMOVAL
Suspend the rear brake caliper from the body with wire, etc.
to prevent it from falling.
Caution
If the vehicle is equipped with the Brembo disc brake,
during maintenance, take care not to contact the parts or
tools to the caliper because the paint of caliper will be
scratched. And if there is brake fluid on the caliper, wipe
out quickly.
A
B" DRIVE SHAFT NUT REMOVAL
Caution
Do not apply pressure to wheel bearing by the vehicle
weight to avoid possible damage to wheel bearing before
tightening drive shaft nut fully.
A
C" REAR HUB ASSEMBLY REMOVAL
1. Using the special tool, remove the drive shaft from the
rear hub assembly.
2. Remove the mounting bolts and remove the rear hub
assembly from the knuckle.
INSTALLATION SERVICE POINT
"
AA DRIVE SHAFT NUT INSTALLATION
1. Assemble the drive shaft washer in the illustrated direction.
2. Tighten the drive shaft nut fully with special tools.
Caution
Do not apply pressure to wheel bearing by the vehicle
weight to avoid possible damage to wheel bearing
before tightening drive shaft nut fully.
3. If the pin hole does not align with another, tighten the
drive shaft nut (less than 250 N
·
m) and find the nearest
hole then bend the split pin to fit in.
MB990767
MB990767
MB990242
MB991354
MB990244
(3)
MB990767
225±25 N·m
Washer
REAR AXLE -
Rear Hub Assembly
27B-27
INSPECTION
WHEEL BEARING ROTATION STARTING TORQUE
CHECK
1. Tighten special tools in rear hub assembly to the specified
torque.
2. Hold rear hub assembly in a vice by way of wooden
block.
3. Measure the wheel bearing rotation torque with special
tools.
Limit: 1.0 N
·
m
4. Hub rotation starting torque must be under the limit value
and there should be no stickiness or roughness when
rotating the hub.
WHEEL BEARING AXIAL PLAY CHECK
1. Check the wheel bearing axial play.
Limit: 0.05 mm
2. If the wheel bearing axial play exceeds the limit value
at the specified torque of (225 ± 25 N
·
m), replace the
rear hub assembly.
Wooden
block
MB991000
(MB990998) MB991017
225 ± 25 N·m
MB990326
Wooden
block
Wooden
block
REAR AXLE -
Knuckle
27B-28
KNUCKLE
REMOVAL AND INSTALLATION
Caution
1. If the vehicle is equipped with the Brembo disc brake, during maintenance, take care not to
contact the parts or tools to the caliper because the paint of caliper will be scratched. And
if there is brake fluid on the caliper, wipe out quickly.
2. With the part marked with *, first temporarily tighten it, then ground the vehicle and tighten
it to specification in unloaded condition.
Pre-removal Operation
Rear Hub Assembly Removal (Refer to P.27-25.)
Post-installation Operation
D
Press dust cover with a finger to check for crack
or damage in the dust cover.
D
Rear Hub Assembly Installation (Refer to P.27-25.)
1
2
3
4
5
6
25 ± 6 N·m
81 ± 6 N·m
81 ± 6 N·m*
88 ± 10 N·m*
81 ± 6 N·m
Removal steps
1. Vehicle speed sensor <Vehicles with
ABS or ACD>
A
A"
2. Knuckle and trailing arm connection
3. Knuckle and lower arm connection
A
A"
4. Knuckle and toe-control arm connec-
tion
A
A"
5. Knuckle and upper arm connection
6. Knuckle assembly
REMOVAL SERVICE POINT
A
A" KNUCKLE AND TRAILING ARM/TOE-CONTROL
ARM/UPPER ARM DISCONNECTION
Caution
1. Use special tools to loosen the nut from the ball joint
instead of removing it.
2. Hang special tools with ropes to prevent them from
falling.
Nut
Cord
Ball joint
MB991113 or
MB990635
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст