Mitsubishi Lancer Evolution 7. Manual — part 256
MANUAL TRANSMISSION - Transmission Control
22A-47
REMOVAL SERVICE POINT
A
A" CLIP/SELECT CABLE CONNECTION
(TRANSMISSION)/SHIFT CABLE (TRANSMISSION)
INSTALLATION
Push up the claws of the clip using a screwdriver, etc., and
then remove the clip from the bracket together with the cables.
INSTALLATION SERVICE POINT
"
AA CLIP/SELECT CABLE AND SHIFT CABLE
ASSEMBLY/SHIFT CABLE CONNECTION/SELECT
CABLE CONNECTION INSTALLATION
1. Set the transmission side shift lever and the passenger
compartment side shift lever to the neutral position.
2. Install the painted part of the shift cable end (transmission
side) and painted part of the select cable (transmission
side) facing the snap pin.
3. After installing the new clip to the cable bracket of the
transmission, install the shift cable and select cable to
the cable bracket.
4. Move the shift lever to all positions and check that the
operation is smooth.
Clip
Claws
Shift cable,
select cable
Neutral position
Select lever
MANUAL TRANSMISSION - Transmission Control
22A-48
SHIFT LEVER ASSEMBLY
DISASSEMBLY AND REASSEMBLY
2
3
4
7
8
10
9
1
5
6
9
3
11
12
14
±
2 N·m
10
±
1 N·m
Disassembly steps
1. Bolt
2. Select lever
3. Bushing
4. Return spring
5. Collar
6. Bolt
7. Cap
8. Shift lever
9. Shift lever bushing
10. Distance piece
11. Bushing
12. Base block
MANUAL TRANSMISSION - Transfer Assembly
22A-49
TRANSFER ASSEMBLY
REMOVAL AND INSTALLATION
Pre-removal and Post-installation Operation
D
Under Cover Removal and Installation (Refer to GROUP 51 - Front Bumper.)
D
Side Under Cover Removal and Installation
D
Transmission Oil Draining and Supplying (Refer to P.22A-40.)
D
Transfer Oil Draining and Supplying (Refer to P.22A-40.)
D
Engine Coolant Draining and Supplying (Refer to GROUP 14 - On-vehicle Service.)
D
Crossmember Bar Removal and Installation (Refer to GROUP 32 - Engine Roll Stopper, Centermember.)
D
Front Exhaust Pipe Removal and Installation (Refer to GROUP 15 - Exhaust Pipe and Main Muffler.)
D
Battery and Battery Tray Removal and Installation
D
Air Cleaner, Air Intake Hose Removal and Installation (Refer to GROUP 15 - Air Cleaner.)
D
Secondary Air Hose Removal and Installation (Refer to GROUP 15 - Secondary Air Control System.)
D
Strut Tower Bar Removal and Installation (Refer to GROUP 42.)
D
Air Hose E, Air By-pass Hose and Air By-pass Valve, Air Pipe C, Air Hose D, Air Pipe B, Air Hose A Removal and
Installation (Refer to GROUP 15 - Intercooler.)
D
Radiator Removal and Installation (Refer to GROUP 14.)
D
Bleeding and Hydraulic Pressure Check <ACD> (Refer to P.22A-42, 43) <after installation only>
1
2
3
4
5
6
7
8
25
±
5 N·m
108
±
10 N·m
39
±
5 N·m
39
±
5 N·m
245
±
29 N·m
Removal steps
1. Stabilizer bar connection
2. Stabilizer link
3. Wheel speed sensor cable clamp
and brake hose clamp
A
A"
4. Tie rod end connection
5. Lower arm ball joint connection
A
B"
6. Drive shaft <L.H.> connection
A
B"
7. Drive shaft <R.H.> connection
A
C"
8. Output shaft
MANUAL TRANSMISSION - Transfer Assembly
22A-50
11
12
9
10
13
14
15
16
13
59
±
9 N·m
59
±
9 N·m
44
±
5 N·m
69
±
10 N·m
52
±
7 N·m*
52
±
7 N·m*
69
±
10 N·m
9. Rear roll stopper connection bolt
10. Centermember assembly
11. Front propeller shaft
(Refer to GROUP 25.)
12. Transfer oil pressure hose assem-
bly <Vehicle of ACD, ACD+AYC>
13. Gasket
<Vehicle of ACD, ACD+AYC>
14. Dust seal guard
A
D"
15. Transfer assembly
16. O-ring
Caution
*: Indicates parts which should be initially tightened,
and then fully tightened after placing the vehicle
horizontally and loading the full weight of the engine
on the vehicle body.
REMOVAL SERVICE POINTS
A
A" TIE ROD END DISCONNECTION
Caution
1. Loosen the nut only; do not remove it from the ball
joint. Otherwise ball joint thread will be damaged.
2. The special tool should be suspended by a cord to
prevent it from coming off.
MB991113 or
MB990635
Cord
Ball joint
Nut
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст